# CKUKER.MAK / ckuker.mak / makefile / Makefile # Fri Sep 6 23:23:25 1996 # CKVER= "6.0.192" # # -- Makefile to build C-Kermit for UNIX and UNIX-like systems -- # # Author: Frank da Cruz, Columbia University # 612 West 115th Street, New York NY 10025-7799, USA. # E-mail: fdc@columbia.edu # Fax: +1 212 662-6442. # Web: http://www.columbia.edu/kermit/ # # Copyright (C) 1985, 1996, Trustees of Columbia University in the City of New # York. The C-Kermit software may not be, in whole or in part, licensed or # sold for profit as a software product itself, nor may it be included in or # distributed with commercial products or otherwise distributed by commercial # concerns to their clients or customers without written permission of the # Office of Kermit Development and Distribution, Columbia University. This # copyright notice must not be removed, altered, or obscured. # # CAREFUL: Don't put the lowercase word "if", "define", or "end" as the first # word after the "#" comment introducer in the makefile, even if it is # separated by whitespace. Some versions of "make" understand these as # directives. Uppercase letters remove the danger, e.g. "# If you have..." # # WARNING: This is a huge makefile, and it contains nested makes. # Some "make" programs run out of memory. If this happens to you, edit # away the parts that do not apply to your system and try again. # # For 2.10 or 2.11 BSD on DEC PDP-11s, use the separate makefile, ckubs2.mak. # For Plan 9, use ckpker.mk. # # C-Kermit can also be built for other systems not supported by this # makefile, including VAX/VMS and OpenVMS, Data General AOS/VS, OS/2, the # Apple Macintosh, Stratus VOS, Apollo Aegis, the Commodore Amiga, OS-9, and # the Atari ST. They have their own separate build procedures. See the # file CKAAAA.HLP for information. # # INSTALLATION NOTES: # # Rename this file to "makefile" or "Makefile" if necessary. Pick out the # entry most appropriate for your UNIX system from the list below and # then give the appropriate "make" command, for example "make bsd", "make # sys5r4", "make posix". The make targets, hundreds of them, are listed # below. If you experience any difficulties with the build procedure, then # please also read any comments that accompany the make entry itself (search # for the make entry name on the left margin). # # For more detailed installation instructions, read the files ckuins.doc and # ckccfg.doc. For descriptions of known problems and limitations, read the # files ckcker.bwr and ckuker.bwr (the "beware files"). # # Most entries build C-Kermit with its symbol table included. To reduce the # size of the executable program, add "LNKFLAGS=-s" to the end of your 'make' # command or to the makefile entry, or 'strip' the executable after # building. To further reduce the size after building, use 'mcs -d' if your # system has such a command. For further details on size reduction, read # ckccfg.doc to find out how to remove unneeded features. # # TCP/IP networking support: If your C-Kermit version does not include TCP/IP # networking, but your UNIX system does, try adding -DTCPSOCKET to the CFLAGS # of your makefile entry. If that doesn't work, look at some of the other # entries that include this flag for ideas about what libraries might need to # be included, etc. NOTE: In some cases (certain versions of SCO or HP-UX), # you might need not only a C compiler, but also a "TCP/IP developers kit" # for the required object libraries and header files. # # Fullscreen file transfer display support: If you are going to use C-Kermit # for establishing connections (dialed, network, etc), you can configure it # to produce a formatted file transfer display by including the curses library # and adding -DCK_CURSES to the CFLAGS for your option, and linking with the # appropriate libraries. There are many examples below, usually ending in # "c", like rs6000c, du42c, sunos41c, etc. Also add -DCK_WREFRESH if your # curses library includes clearok() and wrefresh() functions (or remove # -DNOWREFRESH if the linker complains that it can't find these functions). # After building, you still have to SET FILE DISPLAY FULLSCREEN to get the # formatted screen display. # # Please report modifications, successes, failures (preferably with fixes) or # successes to the author. # # MAKE COMMANDS FOR DIFFERENT UNIX PLATFORMS AND VERSIONS: # # + Marks those that have been tested successfully with C-Kermit 5A or later. # - Marks those that are known not to work in version 5A or later. # ? Marks those as yet untested in version 5A or later. Some of these have # never been tried, others are known to have worked in C-Kermit version 4 # (1985-1989), which was considerably smaller, but have not been tested # in version 5A. # # + for 386BSD (Jolix) 0.0, 0.1, "make 386bsd" (see comments in entry), # or (preferably, if it works) "make bsd44" or "make bsd44c". # + for Acorn RISCiX, "make riscix" or "make riscixgcc" # + for Alliant FX/8 with Concentrix 4.1 or later, "make bsdlck" # + for Altos 486, 586, 986 with Xenix 3.0, "make altos" # + for Altos ACS68000, 8Mhz 68000, UNIX System 3 Rel 2, 512K, "make altos3" # ? for Amdahl UTS 2.4 on IBM 370 series & compatible mainframes, "make uts24" # + for Amdahl UTSV IBM 370 series & compatible mainframes, "make utsv" # + for Amdahl UTSV IBM 370 series mainframes with TCP/IP, "make utsvtcp" # + for Amdahl mainframes with UNIX System V R 5.2.6b 580, "make sys3" # + for Apollo Aegis 9.x, DOMAIN/IX 9.x, "make aegis" # ? for Apollo DOMAIN/IX, if the above fails, try "make apollobsd" # + for Apollo with SR10.0 or later, BSD environment, "make sr10-bsd" # + for Apollo with SR10.0 or later, System V environment, "make sr10-s5r3" # + for Apple Macintosh II with A/UX pre-3.0, "make aux", "auxgcc" or "auxufs" # + for Apple Macintosh with A/UX 3.0 and gcc, "make aux3gcc" or aux3gccc # ? for Apple Macintosh with Minix 1.5.10, "make minix68k" or "make minixc68" # ? for Arix System 90 with AT&T SVR3, "make sys5r3na" # ? for AT&T 6300 with IN/ix, "make sys5" # + for AT&T 6300 PLUS, "make att6300" or (with no debugging) "make att6300nd" # + for AT&T 6386 WGS UNIX PC, "make sys5r3" # + for AT&T 3B2, 3B20 systems, "make att3bx" or "make att3bxc" # + for AT&T 3B1, 7300 UNIX PC, "make sys3upc", "sys3upcg" (gcc), "sys3upcold", # or (for fullscreen curses display) "make sys3upcc", "sys3upcgc" (gcc) # or "make sys3upcx" (see entries for more explanation), # or (for fullscreen curses display and shared library) "make sys3upcshcc" # or for minimum-size interactive version for systems with small memories # "make sys3upcm" or (with gcc) "make sys3upcgm". # + for AT&T System III/System V R2 or earlier, "make sys3" or "make sys3nid" # + for AT&T System III/System V with Honey DanBer UUCP, "make sys3hdb" # + for AT&T System V on DEC VAX, "make sys3" or "make sys5r3" # + for AT&T System V R3, use "make sys5r3" or "make sys5r3c" # + for AT&T System V/386 R320.0 Versyss Systems, use "make sys5r3" # or "make sys5r3c" with KFLAGS=-DNONAWS. # + for AT&T System V R4, "make sys5r4", "make sys5r4sx", or "make sys5r4nx", # or if the ANSI C function prototyping makes trouble, add -DNOANSI, # as in "sys5r4sxna" entry # + for AT&T System V R4 with bundled TCP/IP, "make sys5r4netc", ... # + for AT&T System V R4 with Wollongong TCP/IP, "make sys5r4twg", ... # + for AT&T (USL) System V R4.2 use the sys5r4* entries. # + for Atari Falcon with MiNT, "make posix" # + for Atari ST with Minix ST 1.5.10.3, "make minix68k" or "make minixc68" # ? for BBN C/70 with IOS 2.0, "make c70" # + for BeBox with Be OS 1.x DR7, "make beboxdr7" # Compiles OK but doesn't link with default linker which is limited to 64K. # Links OK with "Code Warrior Gold". Many hacks in the source code need # to be removed when DR8 and later come out. # + for BeBox with Be OS 1.x DR8, "make bebox" # ? for Bell Labs UNIX Version 6 (6th Edition), there is no makefile entry. # + for Bell Labs UNIX Version 7 (7th Edition), "make v7" (but see notes below) # ? for Bell Labs Research UNIX Version 8, "make bellv10" # ? for Bell Labs Research UNIX Version 9, "make bellv10" # + for Bell Labs Research UNIX Version 10, "make bellv10" # + for Bell Labs / Lucent Plan 9, use separate makefile ckpker.mk: # can be built for Intel, MIPS, 680x0, and PowerPC. # + for BSDI/386 1.x, "make bsdi" # + for BSDI/386 2.x, "make bsdi" # + for Berkeley Unix 2.4, "make v7" (but read v7 material below) # ? for Berkeley Unix 2.9 (DEC PDP-11 or Pro-3xx), "make bsd29" # + for Berkeley Unix 2.10, use ckubs2.mak (a separate makefile) # + for Berkeley Unix 2.11, use ckubs2.mak (a separate makefile) # This makefile is too big. Read the instructions in ckubs2.mak. # Rename ckubs2.mak to makefile, then "make bsd210" or "make bsd211". # + for Berkeley Unix 4.1, "make bsd41" # + for Berkeley Unix 4.2, "make bsd" (tested with 4.2 and 4.3) # + for Berkeley Unix 4.2 or 4.3 with HoneyDanBer UUCP, "make bsdhdb" # + for Berkeley Unix 4.3, "make bsd43" (uses acucntrl program for locks) # + for Berkeley Unix 4.3 without acucntrl program, "make bsdlck" or "make bsd" # ? for Berkeley Unix 4.3-Tahoe, same as 4.3 BSD # + for Berkeley Unix 4.3-Reno, "make bsd43" or "make bsd44" or "make bsd44c" # + for Berkeley Unix 4.3-Carson City, "make bsd44" or "make bsd44c" # + for Berkeley Unix 4.4-Networking/2 or -Alpha, "make bsd44" or "make bsd44c" # + for Berkeley Unix 4.4, "make bsd44" or "make bsd44c" # + for Berkeley Unix 4.4-Lite, "make bsd44" or "make bsd44c" # + for Bull DPX/2 with BOS/X, "make bulldpx2" # ? for Cadmus, "make sys3" # ? for Callan Unistar, "make sys3" # ? for CDC VX/VE 5.2.1 System V emulation, "make vxve" # + for Charles River Data Systems Universe 680x0 with UNOS 9.2, maybe # also other UNOS versions, "make crds" # ? for CIE Systems 680/20 with Regulus, "make cie" # + for Commodore Amiga 3000UX Sys V R4, "make sys5r4sx" # + for Commodore Amiga 3000UX Sys V R4 and TCP/IP, "make svr4amiganet" # ? for Commodore Amiga with Minix 1.5.10, "make minix68k" of "make minixc68" # + for Concurrent/Masscomp with RTU 4.0 or later, BSD environment, "make # rtubsd", "make rtubsd2", "make rtubsd3" (depending on where ndir.h # is stored, see entries below). # ? for Concurrent/Masscomp with RTU 4.0 or later, System V R2, "make rtus5" # + for Concurrent/Masscomp with RTU 5.0 or later, System V R3, "make rtusvr3" # + for Concurrent (Perkin-Elmer) 3200 series, "make sys5". # + for Concurrent (Perkin-Elmer) 3200 series with , "make ccop1" # + for Consensys UNIX SV/386 R4V3, "make sys5r4sxtcpc" or "make sys5r4sx" # ? for Convergent with CTIX Sys V R2, "make sys5" # + for Convergent with CTIX 6.4.1, "make ctix" # + for Convex C1, "make convex" # + for Convex C210 with Convex/OS 8, "make convex8" # + for Convex C2 with Convex/OS 9.1, "make convex9" # + for Convex C2 with Convex/OS 10.1 and gcc 2.x, "make convex10gcc" # + for Cray Research X/MP or YMP or C90 with UNICOS 6.x (System V R3), # "make cray" # + for Cray Research X/MP or YMP or C90 with UNICOS 7.x (System V R4), # "make cray" # + for Cray Research X/MP or YMP or C90 with UNICOS 8.0 Alpha, "make cray8" # + for Cray Computer Cray-2 or Cray3 with CSOS, "make craycsos" # + for Cyber 910 (Silicon-Graphics Iris) with Irix 3.3, "irix33" # + for Data General AViiON with DG/UX 5.4, "make dgux540" # or "make dgux540c" (compile ckwart separately if necessary) # + for Data General AViiON with DG/UX 5.4R3.00, "make dgux543c" # + for DG/UX 5.4 R4.11 on AViiON Intel models, "make dgux544i" or dgux544ic. # + for Data General AViiON with DG/UX 4.3x using Sys V-isms, "make dgux430" # ? for Data General AViiON with DG/UX 4.3x using BSD-isms, "make dgux430bsd" # ? for Data General AViiON, earlier UNIX versions, # "make sys5r3" (maybe compile ckwart separately, or "touch ckcpro.c") # ? for Data General MV systems with DG/UX, ??? # + for Data General MV systems with MV/UX, use AOS/VS C-Kermit (CKDKER.MAK) # + for Data General MV systems with AOS/VS, use CKDKER.MAK. # + for DEC PDP-11 with Berkeley UNIX 2.x, see Berkeley UNIX 2.x. # ? for DEC PDP-11 with Mini-UNIX (Bell 6th Edition for PDP-11 with no MMU), # probably no way to fit C-Kermit without I&D space. # ? for DEC PDP-11 with Ultrix-11 3.x, ??? (probably needs overlays) # + for DEC VAX with Ultrix 1.x "make bsd" # + for DEC VAX with Ultrix 2.x "make ultrix2s" # + for DEC VAX or DECstation with Ultrix 3.0, 3.1, "make ultrix3x" # + for DECstation or VAX with Ultrix 4.0 or 4.1, "make ultrix40" # + for DECstation or VAX with Ultrix 4.2 or later, "make ultrix42" or # "make ultrix42c" # + for DECstation 5000/50, /150 or /260 (R4x00 MIPS CPU), Ultrix 4.3A or later # "make ultrix43-mips3" or "make ultrix43c-mips3" # + for DECstation or VAX with Ultrix 4.2, Sys V R4 world, "make du42s5r4" # + for DECstation or VAX with Ultrix 4.x, POSIX world, "make posix" # + for DECstation with Ultrix 4.3, "make ultrix42" # + for DECstation 5000/50 or /150 or /260 (R4x00 MIPS CPU), Ultrix 4.3A/4.4 # "make ultrix43c-mips3" or "make ultrix44-mips3" # ? for DECstation (MIPS) with Berkeley Sprite, "make bsd44"? # + for DECstation (MIPS) with OSF/1 V1.0 to 1.3, "make dec-osf" # + for DEC Alpha with OSF/1 1.0 to 1.3, "make dec-osf" # + for DEC PC 486 with OSF/1, "make dec-osf" # + for DEC Alpha with OSF/1 2.x, "make dec-osf20" # + for DEC Alpha with OSF/1 3.0, "make dec-osf30" # + for DEC Alpha with Digital UNIX 3.2, "make du32" # + for DEC Alpha with Digital UNIX 4.0, "make du40" # - for DEC Pro-350 with Pro/Venix V1.x, "make provx1" (version 5A is too big) # ? for DEC Pro-350 with Pro/Venix V2.0 (Sys V), "make sys3nid" # ? for DEC Pro-380 with Pro/Venix V2.0 (Sys V), "make sys3" or "make sys3nid" # ? for DEC Pro-380 with 2.9, 2.10, or 2.11 BSD, "make bsd29" or "make bsd210" # + for Dell UNIX Issue 2.x (= USL Sys V/386 R4.x + fixes), "make dellsys5r4" # or "make dellsys5r4c" # + for DIAB DS90 with DNIX (any version) create an empty if # this file does not already exist (or add -DNOFILEH to the make entry). # + for DIAB DS90 or LUXOR ABC-9000 with pre-5.2 DNIX, add "getcwd" to libc.a # (see ckuins.doc), then "make dnixold". # + for DIAB DS90 with DNIX 5.2 (Sys V.2) or earlier, "make dnix", # "make dnixnd", or (to add curses and TCP/IP) "make dnixnetc", # + for DIAB DS90 with DNIX 5.3 (Sys V.3), "make dnix5r3" # + for DIAB DS90 with DNIX 5.3 (Sys V.3) and TCP/IP, "make dnix5r3net" # + for DIAB DS90 with DNIX 5.3 2.2 (Sys V.3), ANSI C, "make dnix5r3ansi" # or, to include TCP/IP, "make dnix5r3ansinet", # but you have to fix a bug in /usr/include/stdlib.h first: # change "extern void free(char *str);" to "extern void free(void *str);" # + for Dolphin Server Technology Triton 88/17 with SV/88 R3.2, "make sv88r32" # + for Encore Multimax 310, 510 with Umax 4.2, "make umax42" # + for Encore Multimax 310, 510 with Umax 4.3, "make umax43" # + for Encore Multimax 310, 510 with Umax V 2.2, use Berkeley cc, "make bsd" # + for Encore 88K with Umax V 5.2, "make encore88k" # + for ESIX System V R4.0.3 or 4.04 with TCP/IP support, "make esixr4" # + for Everex STEP 386/25 Rev G with ESIX Sys V R3.2D, "make sys5r3" # ? for Fortune 32:16, For:Pro 1.8, "make ft18" # + for Fortune 32:16, For:Pro 2.1, "make ft21" # + for FPS 500 with FPX 4.1, "made bsd" # + for FreeBSD 1.0, "make freebsd" # + for FreeBSD 2.0, "make freebsd2" # + for Harris HCX-2900, "make sys5r3" # ? for Harris Night Hawk 88K or 68K with CX/UX pre-6.1, "make sys5r3" # + for Harris Night Hawk 88K or 68K with CX/UX 6.1 or later, "make cx_ux" # ? for Heurikon, "make sys3" # ? for HP-3000, MPE/ix, "make posix"? # + for HP-9000 Series 500, HP-UX 5.21 with WIN/TCP 1.2 "make hpux500wintcp" # + for HP-9000 Series, HP-UX < 6.5, without long filenames, no job control, # "make hpuxpre65" # + for HP-9000 Series, HP-UX pre-7.0, without long filenames, "make hpux" # + for HP-9000 Series, HP-UX 6.5, without long filenames, # "make hpux65" or "make hpux65c" # + for HP-9000 Series, HP-UX 7.0 or later, no long filenames, "make hpux7sf" # or (to include tcp/ip, curses, etc) "make hpux7sftcpc" # + for HP-9000 Series with HP-UX Sys V R2, BSD long names, "make hpuxlf" # + for HP-9000 Series with HP-UX Sys V R2, dirent long names, "make hpuxde" # or (to include TCP/IP support) "make hpuxdetcp" # + for HP-9000 Series with HP-UX Sys V R3, "make hpuxs5r3" # + for HP-9000 Series with HP-UX 7.0, TCP/IP, long filenames, "make hpux70lfn" # + for HP-9000 300/400 Series (680x0) with HP-UX 8.0, TCP/IP, "make hpux80" # or "make hpux80c" # + for HP-9000 700/800 Series (PA-RISC), HP-UX 8.0, TCP/IP, "make hpux80pa" # or "make hpux80pac" # + for HP-9000 Series with HP-UX 8.0, no TCP/IP, long filenames, # "make hpux80notcp" or "make hpuxde" # + for HP-9000 Series, HP-UX 9.0 - 9.10, TCP/IP, curses, restricted compiler # (no optimization, no ANSI), all models, "make hpux90". Read the hpux90 # entry below for more info. # + for HP-9000 700 and 800 Series, HP-UX 9.x, TCP/IP, curses, # HP optimizing ANSI C compiler, "make hpux90o700". # + for HP-9000 with Motorola CPUs, HP-UX 9.x, TCP/IP, curses, # HP optimizing ANSI C compiler, "make hpux90mot". # + for HP-9000 on other CPUs, HP-UX 9.x, TCP/IP, curses, # HP optimizing ANSI C compiler, "make hpux90o". # + for HP-9000 series, HP-UX 9.x, TCP/IP, curses, gcc, all models, # "make hpux90gcc" # + for HP-9000 700/800 Series, HP-UX 10.00,10.01,10.10,10.20,10.30, TCP/IP, # curses, restricted compiler (no optimization, no ANSI) "make hpux100". # + for HP-9000 700/800 Series, HP-UX 10.00,10.01,10.10,10.20,10.30, TCP/IP, # curses, HP ANSI/optimizing compiler "make hpux100o" or "make hpux100o+" # ? for IBM 370 Series with IX/370, "make ix370" # + for IBM 370 Series with AIX/370 1.2, "make aix370" # ? for IBM 370 Series with AIX/370 3.0, "make aix370" # + for IBM 370 Series with AIX/ESA 2.1, "make aixesa" # - for IBM PC/AT 286 & compatibles with Mark Williams Coherent OS, # command-line-only version, "make coherent" (version 5A is too big) # + for IBM PC 386 & compatibles with Mark Williams Coherent OS, # minimum interactive version, "make coherentmi" # + for IBM PC 386 & compatibles with Mark Williams Coherent OS, # full interactive version, prior to v4.2, "make coherentmax" # + for IBM PC 386 & compatibles with Mark Williams Coherent OS 4.2, # "make coherent42" # + for IBM PC 386 & compatibles with LynxOS 2.0 or 2.1, "make lynx21" # + for IBM PC 386 & compatibles with LynxOS 2.2, "make lynx" # - for IBM PC/AT & compatibles with original MINIX, "make minix" (too big) # + for IBM PC/AT & compatibles with MINIX, new compiler, "make minixnew" # + for IBM PC family, 386-based, with MINIX/386, "make minix386" # or if you have GNU CC, "make minix386gcc" # + for IBM PS/2 with PS/2 AIX 1.0, 1.1, or 1.2, "make ps2aix" on make level # 1009 with U401450 # + for IBM PS/2 with PS/2 AIX 1.3, "make ps2aix3" # + for IBM RISC System/6000 with AIX 3.0 or 3.1 "make rs6000" or # "make rs6000c" on make level 2008, 3.1.8 # + for IBM RISC System/6000 with AIX 3.2.0 thru 3.2.5 # "make rs6aix32" or "make rs6aix32c" # + for IBM RISC System/6000 with AIX 4.1 or AIX 4.1.1, "make rs6aix41c" # ? for IBM RT PC with AIX 2.1, "make sys3" # + for IBM RT PC with AIX 2.2.1, "make rtaix" or "make rtaixc" # ? for IBM RT PC with ACIS 4.2, "make bsd" # + for IBM RT PC with ACIS 4.3, "make rtacis" or "make bsd KFLAGS=-DNOANSI" # + for IBM RT PC with 4.3BSD/Reno, "make bsd44" or "make bsd44c" # + for ICL DRS400 or 400E, "make iclsys5r3" # + for ICL DRS3000 (80486) with DRS/NX, "make iclsys5r4_486" # + for ICL DRS6000 (SPARC) with DRS/NX, "make iclsys5r4" # + Integrated Solutions Inc V8S VME 68020, "make isi" # + for Intel 302 with Bell Tech Sys V/386 R3.2, "make sys5r3" # ? for Intel Xenix/286, "make sco286" # ? for Interactive System III (PC/IX), "make pcix" or "make is3" # + for Interactive System III (PC/IX) with gcc, "make is3gcc" # + for Interactive 386/ix 1.0.6 with TCP/IP networking, "make is5r3net2" # + for Interactive 386/ix 2.0.x, "make is5r3" or (POSIX) "make is5r3p" # + for Interactive 386/ix 2.0.x with TCP/IP networking, "make is5r3net" # or "make is5r3net2" # + for Interactive 386/ix 2.2.1, job control, curses, no net, gcc, # "make is5r3gcc" # + for Interactive UNIX Sys V R3.2 V2.2 - 4.0 without TCP/IP, "make is5r3jc" # + for Interactive UNIX Sys V R3.2 V2.2 - 4.0 with TCP/IP, "make is5r3netjc" # + for Intergraph Clipper, "make clix" or "make clixnetc" # + for Jolix (see 386BSD) # + for Linux, "make linux" or (to remove TCP/IP) "make linuxnotcp". # For static linking, use "make linuxs". IMPORTANT: Read the comments # that accompany the "linux:" entry. # + for Linux with lcc compiler, "make linuxnotcp-lcc" # + for Luxor ABC-9000 (DIAB DS-90) with pre-5.2 DNIX, add "getcwd" to libc.a # (see ckuins.doc), then "make dnixold". # + for Mach 2.6 on (anything, e.g. DECstation), "make bsd42" or "make bsd43". # + for MachTen (Tenon) 2.1.1.D on (e.g.) Apple Powerbook, "make machten". # ? for Masscomp RTU AT&T System III, "make rtu" # for other Masscomp, see Concurrent. # ? for Microport SV/AT (System V R2), "make mpsysv" (last edit tested: 144) # + for Microport SVR4 2.2, 3.1, or 4.1 "make sys5r4sx" # ? for Microsoft,IBM Xenix (/286, PC/AT, etc), "make xenix" or "make sco286" # + for MIPS System with RISC/os (UMIPS) 4.52 = AT&T SVR3, "make mips" # or "make mipstcpc" # ? for MkLinux on Power Macintosh, "make linux" # + for Modcomp 9730, Real/IX, "make sys5r3" (or modify to use gcc = GLS cc) # + for Modcomp Realstar 1000 with REAL/IX D.1, "make sv88r32" # ? for Motorola Four Phase, "make sys3" or "make sys3nid" # + for Motorola Delta System V/68 R3, "make sv68r3" # + for Motorola Delta System V/68 R3V5, "make sv68r3v5" # + for Motorola Delta System V/68 R3V5.1, "make sv68r3v51" # + for Motorola Delta System V/68 R3V6 with NSE TCP/IP, "make sv68r3v6" # + for Motorola Delta System V/88 R32, "make sv88r32" # + for Motorola Delta System V/88 R40, "make sv88r40" # + for Mt Xinu Mach386 on 386/486-based PCs, "make bsd43" # ? for NCR Tower 1632, OS 1.02, "make tower1" # + for NCR Tower 1632 or Minitower with System V R2, "make sys3" # or "make sys3nv" # + for NCR Tower 32, OS Release 1.xx.xx, "make tower32-1" # + for NCR Tower 32, OS Release 2.xx.xx, "make tower32-2" # + for NCR Tower 32, OS Releases based on Sys V R3, "make tower32" # + for NCR Tower 32, OS Releases based on Sys V R3 with gcc "make tower32g" # + for NCR System 3000, AT&T UNIX System V R4 2.0, "make sys5r4sxna" # + for NCR System 3000, AT&T UNIX System V R4 2.0 with Wollongong TCP/IP, # "make sys5r4net2" or "make sys5r4net2c". # Some header files might misplaced; try this: # ln /usr/include/netinet/in.h /usr/include/sys/in.h # ln /usr/include/arpa/inet.h /usr/include/sys/inet.h # ln /usr/include/sys/termiox.h /usr/include/termiox.h # + for NCR System 3000, NCR UNIX 02.02.01, same as above. # + for NCR MP-RAS System V R4 V2.03, same as above. # + for NCR System 3000, NCR UNIX 02.03.x or 02.04.x, "make sys5r4net2c" # + for NetBSD on PC 386/486,..., "make netbsd" or (ncurses) "make netbsdn" # + for NeXT with NeXTSTEP 1.0 through 3.2, "make next" (on a NeXT) # + for NeXT with NeXTSTEP 3.3, "make next33" # + for NeXTSTEP/486, "make next" (on a PC) # + for NeXTSTEP portable binary (runs on Intel or Motorola), "make nextfat" # + for Nixdorf Targon/31, "make t31tos40x" # + for Norsk Data Uniline 88/17 with SV/88 R3.2, "make sv88r32" # for Novell UnixWare - see UnixWare # + for OSF/1 (vanilla, from OS/F), "make posix" # + for OkiStation 7300 Series, "make sys5r4sxtcp" # + for Olivetti LSX-3020 with X/OS R.2.3, "make xos23" or "make xos23c" # ? for OpenBSD, "make netbsd"? # + for Perkin-Elmer (Concurrent) 3200 series, "make sys5". # + for Perkin-Elmer (Concurrent) 3200 series with , "make ccop1" # + for Perkin-Elmer/Concurrent 3200 with Xelos R02, "make ccop1" # + for PFU Compact A Series SX/A TISP V10/E50 (Japan), "make sxae50" # ? for Plexus, "make sys3" # + for Pyramid 9XXX (e.g. 9845) or MIServer T series, OSx 4.4b thru 5.1, # "ucb make pyramid" or for HDB UUCP, "ucb make pyramid-hdb" or: # + for Pyramid MIServer S or ES Series, DataCenter/OSx, "make pyrdcosx" # + for Pyramid MIS-S MIPS R3000, DataCenter OSx System V R4, "make pyrdcosx" # + for POSIX on anything, "make posix" (but adjustments might be necessary). # + for POSIX on SunOS 4.1 or later, "make sunposix" # + for Prime 8000 MIPS, SVR3, "make mips" or "make mipstcpc" # + for QNX 4.0 or 4.1, 16-bit, on 286 PC, Watcom C 8.5, "make qnx16_41" # + for QNX 4.21 - 4.22A (286+), and 4.23 (386+), 16-bit, Watcom C 9.5x, # "make qnx16" # + for QNX 4.21 and above, 32-bit, 386 or above, Watcom C 10.6, "make qnx32" # NOTE: Default is qnx32 ("make qnx") # ? for Ridge 32 (ROS3.2), "make ridge32" # ? for Samsung MagicStation, "make sys5r4" # ? for SCO Xenix 2.2.1 with development system 2.2 on 8086/8 "make sco86" # + for SCO Xenix/286 2.2.1 with development system 2.2 on 80286, "make sco286" # NOTE: reportedly this makefile is too long for SCO Xenix/286 make, but it # works with "makeL", or if some of the other make entries are edited out. # + for SCO Xenix/386 2.2.2, "make sco386" # + for SCO Xenix/386 2.3.x, "make sco3r2" or "make sco3r2x" # + for SCO Xenix/386 SCO 2.3.3 or 2.3.4 with gcc 1.37 or later, # "make sco386gcc" or (to add curses) "make sco386gccc". # + for SCO Xenix/386 or UNIX/386 with Excelan TCP/IP, "make sco3r2net" # or (to add curses support) "make sco3r2netc" or "sco386netc" # + for SCO Xenix 2.3.x with Racal-InterLan TCP/IP, "make sco3r2netri" # + for other UNIX varieties with Racal Interlan TCP/IP, read sco3r2netri entry # + for SCO Xenix 2.3.x with SCO (Lachman) TCP/IP, "make sco3r2lai" # or (to add curses) "make sco3r2laic" # for SCO UNIX... ALSO READ COMMENTS in the SCO UNIX entries for more info! # + for SCO UNIX/386 3.2.0 or 3.2.1, "make sco3r2" or "make sco3r2x" # + for SCO UNIX/386 3.2.2, "make sco3r22" or "make sco3r22gcc" # or "make sco3r22c" # + for SCO UNIX/386 3.2.2 with SCO TCP/IP, "make sco3r22net" # or "make sco3r22netc" (curses) # + for SCO ODT 1.1, "make sco3r22net" or "make sco3r22netc" (curses) # + for SCO UNIX/386 3.2 V4.x, no network support, "make sco32v4" # + for SCO UNIX/386 3.2 V5.0 - see SCO OpenServer. # + for SCO UNIX 3.2v4.x with TCP/IP, for Extended Acer File # System (EAFS), curses, ANSI C compilation, "make sco32v4net" # + for SCO UNIX 3.2v4.2, "make sco_odt30" # # NOTE: Also see below for other entries that are variations on these, # e.g. to compile with gcc rather than the SCO Development System. # Also be sure to read the comments accompanying each SCO entry. # # + for SCO ODT 2.0, "make sco32v4net" # + for SCO ODT 3.0, "make sco_odt30" # + for SCO OpenServer 5.0 (OSR5), "make sco32v5" # + for SCO OpenServer 5.0 (OSR5) with networking, "make sco32v5net" # + for SCO OpenServer 5.0 (OSR5), gcc, "make sco32v5gcc" # + for SCO OpenServer 5.0 (OSR5), gcc, with networking, "make sco32v5netgcc" # + for SCO OpenServer 5.0 (OSR5) as above, ELF binary, "make sco32v5netgccelf" # for SCO UnixWare - see UnixWare # + for Sequent with DYNIX/ptx 1.2.1, "make dynixptx12" # + for Sequent with DYNIX/ptx 1.3 or 1.4 with TCP/IP, "make dynixptx13" # + for Sequent with DYNIX/ptx 2.0 or 2.1 with TCP/IP, "make dynixptx20" # or "dynixptx20c" # + for Sequent with DYNIX/ptx 4.0 V4.1.3 with TCP/IP, "make dynixptx41c" # + for Sequent Balance 8000 or B8 with DYNIX 3.0.xx, "make dynix3" # or "make dynix3noacu" # + for Sequent Symmetry S81 with DYNIX 3.0.xx, "make dynix3" # + for Sequent DYNIX 3.1.xx, "make dynix31" or "make dynix31c" # + for Siemens/Nixdorf SINIX-N MIPS V5.42, "make sinix542" # + for Silicon Graphics Iris System V IRIX 3.2 or earlier, "make iris" # + for Silicon Graphics Sys V R3 with IRIX 3.3 or later, "make sys5r3" # + for Silicon Graphics Iris Indigo with IRIX 4.0 or 5.0, "make irix40" or # (to include Yellow Pages and Curses) "make irix40ypc" # + for Silicon Graphics Iris Indigo or Elan with IRIX 4.0.x with microcode # optimization and -O4, "make irix40u" or "irix40uc" (and read notes # accompanying these entries). # + for Silicon Graphics IRIX 5.1/5.2/5.3, "make irix51". # + for Silicon Graphics models with IRIX 6.0, "make irix60". # + for Solaris 2.0-2.4 on SPARC or Intel, SunPro CC, "make solaris2x", # + or to add SunLink X.25 8.0x support, "make solaris2x25". # + for Solaris 2.0-2.4 on SPARC or Intel, GNU CC, "make solaris2xg". # + for Solbourne 4/500 with OS/MP 4 "make sunos4" # + for Solbourne 4/500 with OS/MP 4.1 "make sunos41" or "make sunos41c" # + for SONY NEWS with NEWS-OS 4.0.1C, "make sonynews" # + for SONY NEWS with NEWS-OS 4.1.2C, "make sonynews" # + for Sperry/UNISYS 5000/20, UTS V 5.2 3R1, "make sys5" # + for Sperry/UNISYS 5000/30/35/50/55, UTS V 5.2 2.01, "make unisys5r2" # + for Sperry/UNISYS 5000/80 with System V R3, "make sys5r3" # + for Sperry/UNISYS 5000/95 with System V R3, "make sys5r3" # For UNISYS SVR3 it might be necessary to "make sys5r3 KFLAGS=-UDYNAMIC" # + for Stardent 1520, "make sys5r3" # + for Stratus, various models, FTX 2.1, probably also 2.2, "make sys5r4" # + for Sun with Sun UNIX 3.5 and gcc, "make sunos3gcc" # + for Sun with pre-4.0 SunOS versions, "make bsd" (or appropriate variant) # + for Sun with SunOS 4.0, BSD environment, "make sunos4" # + for Sun with SunOS 4.0, BSD, with SunLink X.25, make sunos4x25 # + for Sun with SunOS 4.0, AT&T Sys V R3 environment, "make sunos4s5" # + for Sun with SunOS 4.1 or 4.1.1, BSD environment, "make sunos41" # or "make sunos41c" (curses) or "make sunos41gcc" (compile with gcc) # + for Sun with SunOS 4.1.x, BSD, with SunLink X.25 7.00 or earlier, # "make sunos41x25" or "make sunos41x25c" (curses) # + for Sun with SunOS 4.1, 4.1.1, AT&T Sys V R3 environment, "make sunos41s5" # + for Sun with SunOS 4.1, 4.1.1, POSIX environment, "make sunposix" # + for Sun with SunOS 4.1.2, "make sunos41" or any of its variations. # NOTE: All SunOS 4.x systems -- Shared libraries are used by default. # If this causes problems, add -Bstatic to CFLAGS. # NOTE2: When building C-Kermit under SunOS for the BSD universe, # but /usr/5bin/cc is ahead of /usr/ucb/cc in your PATH, add # "CC=/usr/ucb/cc CC2=/usr/ucb/cc" to the make entry. # NOTE3: If an executable built on one type of Sun hardware does not work # on another type, rebuild the program from source on the target machine. # + for Sun with Solaris 1.x use SunOS 4.1 entries. # + for Sun with Solaris 2.0 through 2.5 and SunPro CC, "make solaris2x" # + for Sun with Solaris 2.0 through 2.5 and GNU CC, "make solaris2xg" # + for Tandy 16/6000 with Xenix 3.0, "make trs16" # + for Tektronix 6130/4132/43xx (e.g.4301) with UTek OS, "make utek" # or (for models without hardware flow control), "make uteknohwfc" # + for Tektronix XD88 series with UTekV OS, "make utekvr3" # + for Tri Star Flash Cache with Esix SVR3.2, "make sys5r3" # ? for Unistar, "make sys5" # + for UNISYS S/4040 68040 CTIX SVR3.2 6.4.1, "make ctix" or "make sys5r3" # + for UNISYS U5000 UNIX SVR3 6.x, "make sys5r3" or "make sys5r3c" # + for UNISYS U6000 UNIX SVR4 1.x, "make sys5r4nx" or "make sys5r4nxnetc" # for UNISYS ... (also see Sperry) # for Univel - see UnixWare # + for UnixWare, "make unixware" or "make unixwarenetc" # ? for Valid Scaldstar, "make valid" # ? for Whitechapel MG01 Genix 1.3, "make white" # ? for Zilog ZEUS 3.21, "make zilog" # # The result should be a runnable program called "wermit" in the current # directory. After satisfactory testing, you can rename wermit to "kermit" # and put it where users can find it. # # To remove intermediate and object files, "make clean". # If your C compiler produces files with an extension other than "o", # then "make clean EXT=u", "make clean EXT=s", or whatever. # # To run lint on the source files, "make lintsun", "make lintbsd", # "make lints5", as appropriate. # ############################################################################## # # NOTES FOR V7 AND 2.X BSD (BASED ON VERSION 4E OF C-KERMIT): # # For Unix Version 7, several variables must be defined to the values # associated with your system. BOOTNAME=/edition7 is the kernel image on # okstate's Perkin-Elmer 3230. Others will probably be /unix. PROCNAME=proc # is the name of the structure assigned to each process on okstate's system. # This may be "_proc" or some other variation. See for more # info on your systems name conventions. NPROCNAME=nproc is the name of a # kernel variable that tells how many "proc" structures there are. Again # this may be different on your system, but nproc will probably be somewhere. # The variable NPTYPE is the type of the nproc variable -- int, short, etc. # which can probably be gleaned from . The definition of DIRECT # is a little more complicated. If nlist() returns, for "proc" only, the # address of the array, then you should define DIRECT as it is below. If # however, nlist() returns the address of a pointer to the array, then you # should give DIRECT a null definition (DIRECT= ). The extern declaration in # should clarify this for you. If it is "extern struct proc # *proc", then you should NOT define DIRECT. If it is "extern struct proc # proc[]", then you should probably define DIRECT as it is below. See # ckuv7.hlp for further information. # # For 2.9 BSD, the makefile may use pcc rather than cc for compiles; that's # what the CC and CC2 definitions are for (the current version of the # makefile uses cc for both; this was tested in version 4E of C-Kermit and # worked OK on the DEC Pro 380, but all bets are off for version 5A). 2.9 # support basically follows the 4.1 path. Some 2.9 systems use "dir.h" for # the directory header file, others will need to change this to "ndir.h". # # The v7 and 2.9bsd versions assume I&D space on a PDP-11. When building # C-Kermit for v7 on a PDP-11, you should probably add the -i option to the # link flags. Without I&D space, overlays will be necessary (if available), # or code segment mapping (a`la Pro/Venix) if that's available. # # C-Kermit 5A (and 6.0?) can be built for 2.10 and 2.11BSD, using overlays, # but a separate makefile is used because this one is too big. # ############################################################################## # # V7-specific variables. # These are set up for Perkin-Elmer 3230 V7 Unix: # PROC=proc DIRECT= NPROC=nproc NPTYPE=int BOOTFILE=/edition7 # # ( For old Tandy TRS-80 Model 16A or 6000 V7-based Xenix, use PROC=_proc, # DIRECT=-DDIRECT, NPROC=_Nproc, NPTYPE=short, BOOTFILE=/xenix ) # ########################################################################### # # Compile and Link variables: # # EXT is the extension (file type) for object files, normally o. # See MINIX entry for what to do if another filetype must be used. # EXT=o #LNKFLAGS= SHAREDLIB= CC= cc CC2= cc MAKE= make SHELL=/bin/sh # ########################################################################### # SAMPLE ONLY. # Easy installation. Modify this to suit your own computer's file organization # and permissions. If you don't have write access to the destination # directories, "make install" will fail. In many cases, a real installation # will also require you to chown / chgrp for the UUCP lockfile and/or tty # devices, and perhaps also to chmod +s the appropriate permission fields. WERMIT = makewhat DESTDIR = BINDIR = /usr/local/bin MANDIR = /usr/man/manl MANEXT = l ALL = $(WERMIT) all: $(ALL) install: $(ALL) cp wermit $(DESTDIR)$(BINDIR)/kermit # The following can fail if the program image was already stripped, # for example by the link flags in the makefile entry. # strip $(DESTDIR)$(BINDIR)/kermit chmod 755 $(DESTDIR)$(BINDIR)/kermit cp ckuker.nr $(DESTDIR)$(MANDIR)/kermit.$(MANEXT) # To make sure 'man' notices the new source file and doesn't keep # showing the old formatted version, remove the old formatted version, # something like this: # rm -f $(DESTDIR)$(MANDIR)/../cat$(MANEXT)/kermit.$(MANEXT) # or this (which requires CATDIR to be defined): # rm -f $(DESTDIR)$(CATDIR)/kermit.$(MANEXT) chmod 644 $(DESTDIR)$(MANDIR)/kermit.$(MANEXT) makewhat: @echo 'make what? You must tell which system to make C-Kermit for.' @echo Examples: make hpux90, make sys5r4, make solaris2x, etc. @echo Please read the comments at the beginning of the makefile. ########################################################################### # # Dependencies Section: manpage: ckuker.nr wermit: ckcmai.$(EXT) ckucmd.$(EXT) ckuusr.$(EXT) ckuus2.$(EXT) ckuus3.$(EXT) \ ckuus4.$(EXT) ckuus5.$(EXT) ckuus6.$(EXT) ckuus7.$(EXT) \ ckuusx.$(EXT) ckuusy.$(EXT) ckcpro.$(EXT) ckcfns.$(EXT) \ ckcfn2.$(EXT) ckcfn3.$(EXT) ckuxla.$(EXT) ckucon.$(EXT) \ ckutio.$(EXT) ckufio.$(EXT) ckudia.$(EXT) ckuscr.$(EXT) \ ckcnet.$(EXT) ckusig.$(EXT) $(CC2) $(LNKFLAGS) -o wermit ckcmai.$(EXT) ckutio.$(EXT) \ ckufio.$(EXT) ckcfns.$(EXT) ckcfn2.$(EXT) ckcfn3.$(EXT) \ ckuxla.$(EXT) ckcpro.$(EXT) ckucmd.$(EXT) ckuus2.$(EXT) \ ckuus3.$(EXT) ckuus4.$(EXT) ckuus5.$(EXT) ckuus6.$(EXT) \ ckuus7.$(EXT) ckuusx.$(EXT) ckuusy.$(EXT) ckuusr.$(EXT) \ ckucon.$(EXT) ckudia.$(EXT) ckuscr.$(EXT) ckcnet.$(EXT) \ ckusig.$(EXT) $(LIBS) #Malloc Debugging version mermit: ckcmdb.$(EXT) ckcmai.$(EXT) ckucmd.$(EXT) ckuusr.$(EXT) ckuus2.$(EXT) \ ckuus3.$(EXT) ckuus4.$(EXT) ckuus5.$(EXT) ckuus6.$(EXT) \ ckuus7.$(EXT) ckuusx.$(EXT) ckuusy.$(EXT) ckcpro.$(EXT) \ ckcfns.$(EXT) ckcfn2.$(EXT) ckcfn3.$(EXT) ckuxla.$(EXT) \ ckucon.$(EXT) ckutio.$(EXT) ckufio.$(EXT) ckudia.$(EXT) \ ckuscr.$(EXT) ckcnet.$(EXT) ckusig.$(EXT) $(CC2) $(LNKFLAGS) -o mermit ckcmdb.$(EXT) ckcmai.$(EXT) \ ckutio.$(EXT) ckufio.$(EXT) ckcfns.$(EXT) ckcfn2.$(EXT) \ ckcfn3.$(EXT) ckuxla.$(EXT) ckcpro.$(EXT) ckucmd.$(EXT) \ ckuus2.$(EXT) ckuus3.$(EXT) ckuus4.$(EXT) ckuus5.$(EXT) \ ckuus6.$(EXT) ckuus7.$(EXT) ckuusx.$(EXT) ckuusy.$(EXT) \ ckuusr.$(EXT) ckucon.$(EXT) ckudia.$(EXT) ckuscr.$(EXT) \ ckcnet.$(EXT) ckusig.$(EXT) $(LIBS) ########################################################################### # man page... # # WARNING: Using "cc -E" to preprocess the man page is not portable, but it # works OK in SunOS 4.1.x, HP-UX, etc. We use the preprocessor to produce # custom man pages based on ifdef, else, and endif directives. But the # preprocessor replaces omitted lines by blank lines and comment lines, so we # use grep to filter them out. THIS MEANS THAT THE SOURCE FILE, ckuker.cpp, # MUST NOT CONTAIN ANY BLANK LINES! # ckuker.nr: ckuker.cpp $(CC) $(CFLAGS) -E ckuker.cpp |grep -v "^$$" |grep -v "^\#" > ckuker.nr ########################################################################### # Dependencies for each module... # ckcmai.$(EXT): ckcmai.c ckcker.h ckcdeb.h ckcsym.h ckcasc.h ckcnet.h ckcsig.h \ ckuusr.h ckcpro.$(EXT): ckcpro.c ckcker.h ckcdeb.h ckcsym.h ckcasc.h ckcpro.c: ckcpro.w wart ckcdeb.h ckcsym.h ckcasc.h ckcker.h ./wart ckcpro.w ckcpro.c ckcfns.$(EXT): ckcfns.c ckcker.h ckcdeb.h ckcsym.h ckcasc.h ckcxla.h \ ckuxla.h ckcfn2.$(EXT): ckcfn2.c ckcker.h ckcdeb.h ckcsym.h ckcasc.h ckcxla.h ckuxla.h ckcfn3.$(EXT): ckcfn3.c ckcker.h ckcdeb.h ckcsym.h ckcasc.h ckcxla.h \ ckuxla.h ckuxla.$(EXT): ckuxla.c ckcker.h ckcsym.h ckcdeb.h ckcxla.h ckuxla.h ckuusr.$(EXT): ckuusr.c ckucmd.h ckcker.h ckuusr.h ckcsym.h ckcdeb.h ckcxla.h \ ckuxla.h ckcasc.h ckcnet.h ckuus2.$(EXT): ckuus2.c ckucmd.h ckcker.h ckuusr.h ckcdeb.h ckcxla.h ckuxla.h \ ckcasc.h ckcnet.h ckcsym.h ckuus3.$(EXT): ckuus3.c ckucmd.h ckcker.h ckuusr.h ckcdeb.h ckcxla.h ckuxla.h \ ckcasc.h ckcnet.h ckcsym.h ckuus4.$(EXT): ckuus4.c ckucmd.h ckcker.h ckuusr.h ckcdeb.h ckcxla.h ckuxla.h \ ckcasc.h ckcnet.h ckuver.h ckcsym.h ckuus5.$(EXT): ckuus5.c ckucmd.h ckcker.h ckuusr.h ckcdeb.h ckcasc.h ckcnet.h \ ckcsym.h ckuus6.$(EXT): ckuus6.c ckucmd.h ckcker.h ckuusr.h ckcdeb.h ckcasc.h ckcnet.h \ ckcsym.h ckuus7.$(EXT): ckuus7.c ckucmd.h ckcker.h ckuusr.h ckcdeb.h ckcxla.h ckuxla.h \ ckcasc.h ckcnet.h ckcsym.h ckuusx.$(EXT): ckuusx.c ckcker.h ckuusr.h ckcdeb.h ckcasc.h ckcsym.h ckcsig.h ckuusy.$(EXT): ckuusy.c ckcker.h ckcdeb.h ckcasc.h ckcnet.h ckcsym.h ckucmd.$(EXT): ckucmd.c ckcasc.h ckucmd.h ckcdeb.h ckcsym.h ckufio.$(EXT): ckufio.c ckcdeb.h ckuver.h ckcsym.h ckutio.$(EXT): ckutio.c ckcdeb.h ckcnet.h ckuver.h ckcsym.h ckucon.$(EXT): ckucon.c ckcker.h ckcdeb.h ckcasc.h ckcnet.h ckcsym.h ckcnet.$(EXT): ckcnet.c ckcdeb.h ckcker.h ckcnet.h ckcsym.h ckcsig.h wart: ckwart.$(EXT) $(CC) $(LNKFLAGS) -o wart ckwart.$(EXT) $(LIBS) ckcmdb.$(EXT): ckcmdb.c ckcdeb.h ckcsym.h ckwart.$(EXT): ckwart.c ckudia.$(EXT): ckudia.c ckcker.h ckcdeb.h ckucmd.h ckcasc.h ckcsym.h ckcsig.h ckuscr.$(EXT): ckuscr.c ckcker.h ckcdeb.h ckcasc.h ckcsym.h ckcsig.h ckusig.$(EXT): ckusig.c ckcasc.h ckcdeb.h ckcker.h ckcnet.h ckuusr.h ckcsig.h ########################################################################### # # Entries to make C-Kermit for specific systems. # # Put the ones that need short makefiles first. bsd210: @echo Please use ckubs2.mak to build C-Kermit $(CKVER) for 2.10BSD. bsd211: @echo Please use ckubs2.mak to build C-Kermit $(CKVER) for 2.11BSD. #Apollo Aegis 9.x. Includes TCP/IP support. #You can also add processor-dependent optimization switches like -M570. aegis: @echo Making C-Kermit $(CKVER) for Apollo Aegis 9.x... $(MAKE) wermit "CFLAGS= -DBSD4 -DDYNAMIC -DTCPSOCKET \ -DCK_CURSES -O $(KFLAGS)" "LIBS = -lcurses -ltermcap" #Apple Mac II, A/UX pre-3.0 #Warning, if "send *" doesn't work, try the auxufs makefile entry below. aux: @echo Making C-Kermit $(CKVER) for Macintosh A/UX... $(MAKE) wermit "CFLAGS = -DAUX -DDYNAMIC -DTCPSOCKET \ $(KFLAGS) -i -O" "LNKFLAGS = -i" #Apple Mac II, A/UX pre-3.0, compiled with gcc auxgcc: @echo Making C-Kermit $(CKVER) for Macintosh A/UX... $(MAKE) wermit "CFLAGS = -DAUX -DDYNAMIC -DTCPSOCKET \ -traditional $(KFLAGS) -i -O" "LNKFLAGS = " "CC = gcc" "CC2 = gcc" #Apple Mac II, A/UX, pre-3.0, but with ufs file volumes, uses . auxufs: @echo Making C-Kermit $(CKVER) for Macintosh A/UX... $(MAKE) wermit "CFLAGS = -DAUX -DDYNAMIC -DTCPSOCKET -DDIRENT \ $(KFLAGS) -i -O" "LNKFLAGS = -i" #Apple Mac II, A/UX 3.0, compiled with gcc aux3gcc: @echo Making C-Kermit $(CKVER) for Macintosh A/UX 3.0... $(MAKE) wermit "CFLAGS = -DAUX -DHDBUUCP -DLFDEVNO -DDYNAMIC \ -DTCPSOCKET -DDIRENT $(KFLAGS) -O2" "LNKFLAGS = -s" "LIBS = $(LIBS)" \ "CC=gcc -pipe -traditional" "CC2=gcc -pipe -traditional" #Apple Mac II, A/UX 3.0, compiled with gcc, uses curses aux3cgcc: @echo Making C-Kermit $(CKVER) for Macintosh A/UX 3.0... $(MAKE) "MAKE=$(MAKE)" aux3gcc "KFLAGS=$(KFLAGS) -DCK_CURSES" \ "LIBS = -lcurses $(LIBS)" #Bell Labs Research UNIX V10 #Can't add TCP/IP because there is no sockets library. It would have to #be done using streams, but there is no code in C-Kermit for that. #Remove -DNOJC if desired (if your system has csh, ksh, or bash). bellv10: @echo Making C-Kermit $(CKVER) for Bell Labs Research UNIX V10... $(MAKE) wermit "CFLAGS= -DBELLV10 -DBSD4 -DNDIR -DDYNAMIC -DNOJC \ -DNOSYSIOCTLH -DNOSETREU -DNOSETBUF -DNOCSETS -MINIDIAL $(KFLAGS)" #Berkeley Unix 4.1 bsd41: @echo Making C-Kermit $(CKVER) for 4.1BSD... $(MAKE) wermit "CFLAGS= -DBSD41" "LIBS = -ljobs" #Berkeley 4.2, 4.3, also Ultrix-32 1.x, 2.x, 3.x, many others # Add -O, -DDYNAMIC, -s, etc, if they work. # If you have a version of BSD but signal() is void rather than int, # "make bsd KFLAGS=-DSIG_V". bsd: @echo Making C-Kermit $(CKVER) for 4.2BSD... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET $(KFLAGS)" #Berkeley 4.2, 4.3, minimum size bsdm: @echo Making C-Kermit $(CKVER) for 4.2BSD... $(MAKE) wermit "CFLAGS= -O -DBSD4 -DDYNAMIC -DNODIAL -DNOHELP \ -DNODEBUG -DNOTLOG -DNOSCRIPT -DNOCSETS -DNOICP $(KFLAGS)" \ "LNKFLAGS = -s" #Berkeley Unix with HoneyDanBer UUCP bsdhdb: @echo Making C-Kermit $(CKVER) for 4.2BSD with HDB UUCP... $(MAKE) wermit "CFLAGS= -DHDBUUCP -DBSD4 -DTCPSOCKET $(KFLAGS)" #Berkeley Unix 4.3 with acucntrl program bsd43: @echo Making C-Kermit $(CKVER) for 4.3BSD with acucntrl... $(MAKE) wermit \ "CFLAGS= -DBSD43 -DACUCNTRL -DTCPSOCKET $(KFLAGS) -O" #Ditto, with curses support. bsd43c: @echo Making C-Kermit $(CKVER) for 4.3BSD with acucntrl and curses... $(MAKE) wermit "CFLAGS= -DBSD43 -DACUCNTRL -DTCPSOCKET \ -DCK_CURSES $(KFLAGS) -O" "LIBS=-lcurses -ltermcap" #Berkeley Unix 4.2 or 4.3 with lock directory /usr/spool/uucp/LCK/LCK..ttyxx, #but without acucntrl program bsdlck: @echo Making C-Kermit $(CKVER) for 4.2BSD, /usr/spool/uucp/LCK/... $(MAKE) wermit "CFLAGS= -DLCKDIR -DBSD4 -DTCPSOCKET $(KFLAGS)" #Berkeley UNIX 4.4-Lite, 4.4-Encumbered, Net/2, etc (Post-Reno), #with TCP/IP networking. This includes NetBSD, FreeBSD, etc. #NOTE: This is not a pure POSIX configuration. Using -DPOSIX instead of # -DBSD44 prevents any kind of directory-reading (for wildcard expansion), #and disallows use of ENOTCONN symbol for detecting broken network #connections, and disallows RTS/CTS flow control, and would also require #definition of the appropriate UUCP lockfile convention. #Do not add -DCK_POSIX_SIG without reading first! For example, #sigsetjmp(), etc, tend to be defined but not implemented. bsd44: @echo Making C-Kermit $(CKVER) for 4.4BSD... $(MAKE) wermit \ "CFLAGS= -DBSD44 -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" #Berkeley UNIX 4.4, as above, but with curses for fullscreen display #Please read notes for bsd44 entry just above. bsd44c: @echo Making C-Kermit $(CKVER) for 4.4BSD with curses... $(MAKE) wermit \ "CFLAGS= -DBSD44 -DCK_CURSES -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" \ "LIBS= -lcurses -ltermcap" #NetBSD netbsd: $(MAKE) bsd44c "KFLAGS=$(KFLAGS) -DNOCOTFMC" #NetBSD with ncurses netbsdn: @echo Making C-Kermit $(CKVER) for NetBSD with ncurses... $(MAKE) wermit \ "CFLAGS= -DBSD44 -DCK_CURSES -DDYNAMIC -DTCPSOCKET -DNOCOTFMC \ $(KFLAGS) -O" \ "LIBS= -lncurses -ltermcap" #Acorn RISCiX, based on ... #Berkeley Unix 4.2 or 4.3 with lock directory /usr/spool/uucp/LCK/LCK..ttyxx, #but without acucntrl program riscix: @echo Making C-Kermit $(CKVER) for RISCiX, /usr/spool/uucp/LCK..ttyxx $(MAKE) wermit "CFLAGS= -DBSD42 -DBSD4 -DRISCIX -DNOCSETS \ -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DDIRENT -DCK_CURSES \ -DMAXSP=9024 -DMAXRD=9024 -DSBSIZ=9050 -DRBSIZ=9050 \ -DFTTY=\\\"/dev/serial\\\" -DNOCSETS -DNOCYRIL -DNOSETBUF \ -DNOANSI -w -O2 -fomit-frame-pointer" \ "LIBS= -lcurses -ltermcap " \ "CC= /usr/ucb/cc" \ "CC2= /usr/ucb/cc" #Acorn RISCiX, as above, but using gcc riscix-gcc: @echo Making C-Kermit $(CKVER) for RISCiX, /usr/spool/uucp/LCK..ttyxx $(MAKE) wermit "CFLAGS= -DBSD42 -DBSD4 -DRISCIX -DNOCSETS \ -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DDIRENT -DCK_CURSES \ -DMAXSP=9024 -DMAXRD=9024 -DSBSIZ=9050 -DRBSIZ=9050 \ -DFTTY=\\\"/dev/serial\\\" -DNOCSETS -DNOCYRIL -DNOSETBUF \ -DNOANSI -w -O2 -fomit-frame-pointer" \ "LIBS= -lcurses -ltermcap " \ "CC= gcc -mbsd" \ "CC2= gcc -mbsd" #Tektronix 6130, 4319, 4301, etc, with UTek OS, /usr/spool/uucp/LCK./... #The models that support hardware flow control. utek: @echo 'Making C-Kermit $(CKVER) for 4.2BSD/UTek, hardware flow control' $(MAKE) wermit \ "CFLAGS= -O -DLCKDIR -DBSD4 -DTCPSOCKET -DDYNAMIC \ -DUTEK -DDCLPOPEN -DLOCK_DIR=\\\"/usr/spool/uucp/LCK.\\\" \ -DTRMBUFL=2048 -DCK_DTRCTS $(KFLAGS)" #Tektronix 4315, 4316, 4317 with UTek OS, /usr/spool/uucp/LCK./... #The models that do not fully support hardware flow control. uteknohwfc: @echo 'Making C-Kermit $(CKVER) for 4.2BSD/UTek, no h/w flow control' $(MAKE) wermit \ "CFLAGS= -O -DLCKDIR -DBSD4 -DTCPSOCKET -DDYNAMIC \ -DUTEK -DDCLPOPEN -DLOCK_DIR=\\\"/usr/spool/uucp/LCK.\\\" \ -DTRMBUFL=2048 $(KFLAGS)" #Tektronix XD88 with UTekV OS utekvr3: @echo 'Making C-Kermit $(CKVER) for Tektronix XD88 UTekV R3...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTCPSOCKET -DSYSUTIMEH -DCK_CURSES $(KFLAGS) -O" \ "LIBS= -lcurses" "LNKFLAGS= -s" #Convergent CTIX 6.4.1 ctix: @echo 'Making C-Kermit $(CKVER) for Convergent CTIX 6.4.1' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DTCPSOCKET -DHDBUUCP -DCK_CURSES -DDYNAMIC \ -DNONAWS $(KFLAGS) -XO" "LNKFLAGS=-s" "LIBS=-lsocket -lcurses -lc_s" mcs -d wermit # The following makefile entry should work for any Harris Night Hawk system # (either 88k or 68k based) running release 6.1 or later of the CX/UX # operating system. This is a POSIX and ANSI-C compliant system which also # supports BSD networking. (Earlier CX/UX releases will probably work with # sys5r3, but this has not been verified). # cx_ux: @echo Making C-Kermit $(CKVER) for Harris Night Hawk CX/UX 6.1 or later $(MAKE) wermit \ "CFLAGS=-DPOSIX -DTCPSOCKET -DHDBUUCP -DPID_T=pid_t -DWAIT_T=int \ -Dd_ino=d_fileno -DUID_T=uid_t -DGID_T=gid_t -DDYNAMIC $(KFLAGS) -Xa \ -O3 -g" "LNKFLAGS=-O3" #Perkin-Elmer 3200 Xelos R02 or earlier ccop1: @echo 'Making C-Kermit $(CKVER) for Xelos & Public Domain Dirent calls' @echo 'or System V R2 or earlier...' $(MAKE) wermit \ "CFLAGS = -DATTSV -Dvoid=int -DDIRENT -DCK_CURSES \ $(KFLAGS) -O" "LNKFLAGS =" "LIBS= -lcurses -ltermlib" #Intergraph Clipper 2000, 3000, 4000, 5000, or 6000 with CLIX 3.1 = Sys V R3 #Note, cc has been phased out, acc is used instead. gcc can be substituted. clix: $(MAKE) "CC=acc" "CC2=acc" sys5r3 #Intergraph Clipper, as above plus curses, TCP/IP, job control, HDB UUCP. #Probably, should be added to regular clix entry too. clixnetc: $(MAKE) wermit "CC=acc" "CC2=acc" \ "CFLAGS= -DSVR3JC -DSVR3 -DCK_CURSES -DDIRENT -DCK_NEWTERM \ -DTCP_SOCKET -HDBUUCP -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS=" "LIBS= -lcurses -ltermlib -lbsd" #Mark Williams Coherent 286 or 386 on IBM PC family. #There is a 64K limit on program size, so this is a command-line only version. coherent: $(MAKE) "CFLAGS = -O -DCOHERENT -DDYNAMIC -DNOANSI -DNOICP -DNOSETKEY \ -DNOCSETS -DNOHELP -DNODIAL -DNOSCRIPT -DNODEBUG -DNOTLOG -DNOXMIT \ -DNOMSEND -DNOFRILLS -DNOSYSIOCTLH -DSELECT_H $(KFLAGS) -VSUVAR" wermit #Mark Williams Coherent 386 on IBM PC family. #This will make a "minimum interactive" version - no scripts, #no character sets, no help, no dial, no debug/transaction logging, no #transmit, msend, mail, type, etc. coherentmi: $(MAKE) "CFLAGS = -O -DCOHERENT -DDYNAMIC -DNOANSI -DNOSETKEY \ -DNOSHOW -DNOCSETS -DNOHELP -DNODIAL -DNOSCRIPT -DNODEBUG -DNOTLOG \ -DNOXMIT -DNOMSEND -DNOFRILLS -DNOSYSIOCTLH -DNOSERVER -DNOUUCP \ -DNOSPL -DNOSETBUF -DNOPUSH -DNOMDMHUP -DNOJC -DNOFDZERO -DNOESCSEQ \ -DNOCMDL $(KFLAGS) -VSUVAR -DSELECT_H" wermit #Mark Williams Coherent 386 on IBM PC/AT family. coherentmax: $(MAKE) "CFLAGS = -O -DCOHERENT -DDYNAMIC -DNOANSI -DSELECT_H \ -DNOSYSIOCTLH $(KFLAGS) -VSUVAR" "LNKFLAGS = -O -s" wermit #Mark Williams Coherent 386 4.2 on IBM PC/AT family coherent42: $(MAKE) "CFLAGS = -T0 -O -DCOHERENT -DDYNAMIC -DNOANSI -DSELECT \ -DDIRENT -DCK_CURSES -DCK_NEWTERM -DCK_WREFRESH -DNOSYSIOCTLH \ -DSELECT_H $(KFLAGS) -VSUVAR" "LNKFLAGS = -O -s" \ "LIBS = -lsocket -lcurses" wermit #DEC Ultrix 2.x # Add -O, -DDYNAMIC, -s, etc, if they work. ultrix2x: @echo Making C-Kermit $(CKVER) for Ultrix 2.x ... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DDU2 $(KFLAGS)" du2: $(MAKE) "MAKE=$(MAKE)" ultrix2x #DEC Ultrix 3.1 (and probably also 3.0) ultrix3x: @echo Making C-Kermit $(CKVER) for Ultrix 3.x... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DDIRENT -DSIG_V \ -DDYNAMIC $(KFLAGS) -O" "LNKFLAGS = -s" du3: $(MAKE) "MAKE=$(MAKE)" ultrix3x #DEC Ultrix 4.0 or 4.1 on DECstation, VAXstation, VAX, etc. ultrix40: @echo Making C-Kermit $(CKVER) for Ultrix 4.0 or 4.1... $(MAKE) wermit \ "CFLAGS= -DBSD4 -DTCPSOCKET -DSIG_V -DDYNAMIC -DDU4 \ $(KFLAGS) -Olimit 1450" "LNKFLAGS = -s" du4: $(MAKE) "MAKE=$(MAKE)" ultrix4x #DEC Ultrix 4.2-4.5 on DECstation, DECsystem, VAXstation, VAX, etc. #Like du4, except now C compiler supports -O2 optimization. ultrix42: @echo Making C-Kermit $(CKVER) for Ultrix 4.2 or later... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DSIG_V -DDYNAMIC \ $(KFLAGS) -O2 -Olimit 1750" "LNKFLAGS = -s" du42: $(MAKE) "MAKE=$(MAKE)" ultrix42 #DEC Ultrix 4.2-4.5 on DECstation, DECsystem, VAXstation, VAX, etc. #Like du42, but with curses support added ultrix42c: @echo Making C-Kermit $(CKVER) for Ultrix 4.2 or later... @echo WARNING - If you have problems with the executable @echo then rebuild without -O2. $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DSIG_V -DDYNAMIC \ -DCK_CURSES $(KFLAGS) -O2 -Olimit 1750" "LNKFLAGS = -s" \ "LIBS= -lcurses -ltermcap" du42c: $(MAKE) "MAKE=$(MAKE)" ultrix42c #DEC Ultrix 4.3A or later on DECsystem and DECstation 5000/50, /150 or /260 #with MIPS R4x00 processor. The "-mips3" switch generates R4000-specific #code, which is faster and more compact, but *won't* run on earlier #DECsystems and DECstations. ultrix43-mips3: @echo Making C-Kermit $(CKVER) for Ultrix 4.3A or later, R4000 cpu... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DSIG_V -DDYNAMIC \ $(KFLAGS) -O2 -Olimit 1750 -mips3" "LNKFLAGS = -s -mips3" du43-mips3: $(MAKE) "MAKE=$(MAKE)" ultrix43-mips3 #DEC Ultrix 4.3A or later on MIPS R4x000 based systems. #Like ultrix43-mips3 but with curses support added ultrix43c-mips3: @echo Making C-Kermit $(CKVER) for Ultrix 4.3A or later, R4000 cpu... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DSIG_V -DDYNAMIC \ -DCK_CURSES $(KFLAGS) -O2 -Olimit 1750 -mips3" "LNKFLAGS = -s -mips3" \ "LIBS= -lcurses -ltermcap" du43c-mips3: $(MAKE) "MAKE=$(MAKE)" ultrix43c-mips3 #DEC Ultrix 4.4 on DECstation 5000/50 or /150 with R4000 MIPS processor, #or 5000/260 with R4400. The "-mips3" switch generates R4000-specific code, #which is faster and more compact but *won't* run on earlier DECstations. ultrix44-mips3: @echo Making C-Kermit $(CKVER) for Ultrix 4.4, R4000 cpu ... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET -DSIG_V -DDYNAMIC \ $(KFLAGS) -O2 -Olimit 1450 -mips3" "LNKFLAGS = -s -mips3" du44-mips3: $(MAKE) "MAKE=$(MAKE)" ultrix44c-mips3 #DEC Ultrix 4.2 on DECstation, VAXstation, VAX, etc, System V R4 environment ultrix42s5r4: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4 on Ultrix...' $(MAKE) wermit \ "CFLAGS = -O2 -Olimit 1500 -DSVR4 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DTCPSOCKET $(KFLAGS)" "LNKFLAGS = -s" #OSF/1 osf: $(MAKE) wermit \ "CFLAGS= -DBSD4 -DOSF -D_BSD -DTCPSOCKET -DCK_ANSIC -DSIG_V \ -DDYNAMIC -DKANJI -DCK_CURSES -DCK_RTSCTS $(KFLAGS)" \ "LNKFLAGS = -s" "LIBS = -lbsd -lcurses -ltermcap" #DEC OSF/1 V1.0-1.3 on DECstation, VAX, Alpha, or PC. dec-osf: @echo Making C-Kermit $(CKVER) for DEC OSF/1 V1.x... @echo If you are building for DEC OSF/1 2.0, please use dec-osf20. @echo Remove or adjust -O2 and/or -Olimit if they cause trouble. $(MAKE) osf "KFLAGS= -O2 -Olimit 1460 $(KFLAGS)" #DEC OSF/1 2.0 on Alpha and probably nowhere else. #The only difference from OSF/1 is that optimization is omitted. #The optimized version gets strange runtime errors, like the PAUSE command #not working. Add "-unsigned" to make all chars unsigned. dec-osf20: @echo Making C-Kermit $(CKVER) for DEC OSF/1 V2.0... @echo Optimization omitted because it causes runtime errors. @echo See comments in makefile. $(MAKE) osf "KFLAGS= -DOSF20 $(KFLAGS)" dec-osf30: @echo Making C-Kermit $(CKVER) for DEC OSF/1 V3.0... $(MAKE) osf "KFLAGS= -DOSF30 -O2 -Olimit 1760 $(KFLAGS)" #Digital UNIX 3.2 du32: @echo Making C-Kermit $(CKVER) for Digital UNIX 3.2... $(MAKE) osf \ "KFLAGS= -DOSF32 -DHDBUUCP -O2 -Olimit 1760 $(KFLAGS)" dec-osf32: $(MAKE) "MAKE=$(MAKE)" du32 du40: @echo Making C-Kermit $(CKVER) for Digital UNIX 4.0... $(MAKE) osf \ "KFLAGS= -DOSF40 -DHDBUUCP -unsigned -std1 -O3 -Olimit 1760 $(KFLAGS)" dec-osf40: $(MAKE) "MAKE=$(MAKE)" du40 du40-ridiculous-checking: @echo Making C-Kermit $(CKVER) for Digital UNIX 4.0. @echo Checking everything - assumes DECC... $(MAKE) osf "KFLAGS= -DOSF40 -DHDBUUCP -w0 -warnprotos -check \ -portable -unsigned -std1 -O3 -Olimit 1760 $(KFLAGS)" #Sequent DYNIX/ptx 1.2.1 dynixptx12: @echo Making C-Kermit $(CKVER) for Sequent DYNIX/ptx 1.2.1... $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DPTX \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Sequent DYNIX/ptx 1.3 or 1.4 dynixptx13: @echo Making C-Kermit $(CKVER) for Sequent DYNIX/ptx 1.3 TCP/IP... $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DPTX -DCK_POLL -O \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t -DTCPSOCKET $(KFLAGS) -i" \ "LNKFLAGS = -i" "LIBS = -lsocket -linet -lnsl" #Sequent DYNIX/ptx 2.0, ANSI C compilation #Should work on any hardware platform when DYNIX/ptx runs, including #386, 486, Pentium. dynixptx20: @echo 'Making C-Kermit $(CKVER) for POSIX, Sequent DYNIX/ptx 2.0...' $(MAKE) wermit \ "CFLAGS= -DPOSIX -DHDBUUCP -DDYNAMIC -DTCPSOCKET \ -DWAIT_T=int -DNOSETBUF -DPTX -O" \ "LIBS = -lsocket -linet -lnsl" #Sequent DYNIX/ptx 2.0, ANSI C compilation, with curses dynixptx20c: @echo 'Making C-Kermit $(CKVER) for POSIX, Sequent DYNIX/ptx 2.0...' $(MAKE) wermit \ "CFLAGS= -DPOSIX -DHDBUUCP -DDYNAMIC -DTCPSOCKET \ -DWAIT_T=int -DNOSETBUF -DPTX -DCK_CURSES -DCK_NEWTERM -O" \ "LIBS = -lsocket -linet -lnsl -lcurses -ltermcap" #Sequent DYNIX/ptx 4.0, ANSI C compilation, with curses dynixptx41c: @echo 'Making C-Kermit $(CKVER) for POSIX, Sequent DYNIX/ptx 4.1...' $(MAKE) wermit \ "CFLAGS= -DPOSIX -DHDBUUCP -DDYNAMIC -DTCPSOCKET \ -DWAIT_T=int -DNOSETBUF -DPTX -DCK_CURSES -DCK_NEWTERM -O" \ "LIBS = -lsocket -lnsl -lcurses -ltermcap" #Sequent DYNIX 3.0.x dynix3: @echo Making C-Kermit $(CKVER) for Sequent DYNIX 3.0.x... $(MAKE) wermit \ "CFLAGS= -DBSD43 -DACUCNTRL -DTCPSOCKET -O \ -DPWUID_T=int -DGID_T=int $(KFLAGS)" #Sequent DYNIX 3.0.x, no ACUCNTRL dynix3noacu: @echo Making C-Kermit $(CKVER) for Sequent DYNIX 3.0.x... $(MAKE) wermit "CFLAGS= -DBSD43 -DLCKDIR -DTCPSOCKET -O \ -DUID_T=int -DGID_T=int $(KFLAGS)" #Sequent DYNIX 3.1.x dynix31: @echo Making C-Kermit $(CKVER) for Sequent DYNIX 3.1.x... $(MAKE) wermit \ "CFLAGS= -O -DDYNAMIC -DDCLPOPEN -DLCKDIR -DBSD4 -DTCPSOCKET $(KFLAGS)" #Sequent DYNIX 3.1.2, as above but with curses, to be compiled by gcc 2.3.3. dynix31c: @echo 'Making C-Kermit $(CKVER) for Sequent DYNIX 3.1.2, curses...' $(MAKE) wermit "CFLAGS= -O2 -DDYNAMIC -DDCLPOPEN -DACUCNTRL \ -DBSD43 -DTCPSOCKET -DCK_CURSES -DNOSETBUF -DUID_T=int \ $(KFLAGS)" "LIBS= -lcurses -ltermcap" #Encore, UMAX 4.3 (BSD) but without acucntrl program. encore: $(MAKE) "MAKE=$(MAKE)" umax43 "KFLAGS=$(KFLAGS)" #Encore, as above, but with curses file transfer display included. encorec: $(MAKE) "MAKE=$(MAKE)" umax43 "KFLAGS=-DCK_CURSES $(KFLAGS)" \ "LIBS= -lcurses -ltermcap" #Encore, UMAX 4.3 (BSD) but without acucntrl program. umax43: @echo Making C-Kermit $(CKVER) for Encore UMAX 4.3... $(MAKE) "MAKE=$(MAKE)" PARALLEL=4 wermit \ "CFLAGS= -DBSD43 -DENCORE -DDYNAMIC -DKANJI -DTCPSOCKET $(KFLAGS) -O" #Encore, UMAX 4.2 (BSD) umax42: @echo Making C-Kermit $(CKVER) for Encore UMAX 4.2... $(MAKE) "MAKE=$(MAKE)" PARALLEL=4 wermit \ "CFLAGS= -DBSD4 -DENCORE -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" #Encore 88K UMAX 5.3 with TCP/IP support encore88k: @echo 'Making C-Kermit $(CKVER) for Encore 88K UMAX V, TCP/IP...' $(MAKE) wermit \ "CFLAGS = -q ext=pcc -DSVR3 -DTCPSOCKET -DDIRENT \ -DNOGETID_PROTOS -DHDBUUCP -DDYNAMIC $(KFLAGS) -O" "LNKFLAGS =" #Encore 88K UMAX 5.3 with TCP/IP support encore88kgcc: @echo 'Making C-Kermit $(CKVER) for Encore 88K UMAX V, TCP/IP, gcc...' $(MAKE) wermit CC=gcc CC2=gcc \ "CFLAGS = -DSVR3 -DTCPSOCKET -DDIRENT \ -DNOGETID_PROTOS -DHDBUUCP -DDYNAMIC $(KFLAGS) -O" "LNKFLAGS =" #Berkeley Unix 2.8, 2.9 for PDP-11s with I&D space, maybe also Ultrix-11??? #C-Kermit(5A) is simply too large (even turning off almost every feature #available) to run without both I&D space plus overlays. The old comment #suggested running 'pcc' but that won't help. Changing 'cc' to 'ckustr.sed' #will cause a string extraction to be done, saving D space by moving strings #to a file. bsd29: @echo Making C-Kermit $(CKVER) for 2.8 or 2.9BSD. @echo Read the makefile if you have trouble with this... $(MAKE) ovwermit \ "CFLAGS= -DBSD29 -DNODEBUG -DNOTLOG -DNOCSETS -DNOHELP \ -DNOSCRIPT -DNOSPL -DNOXMIT -DNODIAL $(KFLAGS)" \ "LNKFLAGS= -i -lndir" "CC= cc " "CC2= cc" #Convex C1 with Berkeley Unix convex: @echo Making C-Kermit $(CKVER) for Convex C1 / BSD... $(MAKE) wermit "CFLAGS= -DBSD4 $(KFLAGS) -Dmsleep=mnap" #Convex C210 with Convex/OS 8 convex8: @echo Making C-Kermit $(CKVER) for Convex C210 with OS 8 $(MAKE) wermit \ "CFLAGS= -DBSD4 -DTCPSOCKET -DNODEBUG -DDIRENT -DNOFILEH \ -DDYNAMIC $(KFLAGS) -DSIG_V -Dmsleep=mnap" #Convex C2 with Convex OS 9.1 (should also work with 8.1 or later) #with ANSI C compiler, uses BSD 4.3 uucp lockfile convention. convex9: @echo Making C-Kermit $(CKVER) for Convex C210 with OS 9.1 $(MAKE) wermit \ "CFLAGS= -DPOSIX -DCONVEX9 -DNOIEXTEN -DDIRENT -DNOFILEH -DTCPSOCKET \ -DDYNAMIC -D__STDC__ -DLCKDIR -Dmsleep=mnap -O -ext -tm c1 $(KFLAGS)" \ "LNKFLAGS = -ext" #Convex C2 with Convex OS 10.1 or later #with gcc 2.x C compiler convex10gcc: @echo Making C-Kermit $(CKVER) for Convex C2 with OS 10.1 using gcc $(MAKE) wermit \ "CFLAGS= -DPOSIX -DCONVEX9 -DNOIEXTEN -DDIRENT -DNOFILEH -DTCPSOCKET \ -DDYNAMIC -D__STDC__ -Dmsleep=mnap -O2 $(KFLAGS)" CC=gcc CC2=gcc #Cray X-MP or Y-MP UNICOS 6.x or 7.x. #NOTE: NPROC tells how many parallel makes to run. If your Cray has multiple #processors, you can set NPROC up to the number of CPUs, e.g. NPROC=16. cray: @echo 'Making C-Kermit $(CKVER) for Cray X/Y-MP UNICOS 6.x or 7.0... $(MAKE) wermit NPROC=1 \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DTCPSOCKET $(KFLAGS) -O1" #Cray X-MP or Y-MP UNICOS 8.0 Alpha. cray8: @echo 'Making C-Kermit $(CKVER) for Cray X/Y-MP UNICOS 8.0 Alpha... $(MAKE) wermit NPROC=1 \ "CFLAGS= -DSVR4 -DDIRENT -DHDBUUCP -DTCPSOCKET $(KFLAGS) -O1" #Cray-2 or Cray 3-CSOS #NOTE: NPROC tells how many parallel makes to run. If your Cray has multiple #processors, you can set NPROC up to the number of CPUs, e.g. NPROC=16. craycsos: @echo 'Making C-Kermit $(CKVER) for Cray-2/3 CSOS $(MAKE) wermit NPROC=1 \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DTCPSOCKET \ $(KFLAGS) -DCK_ANSIC -DCK_CURSES" "LIBS=-lnet" #Charles River Data Systems Universe with UNOS Version 9.2 crds: @echo 'Making C-Kermit $(CKVER) for Charles River Data Systems...' make wermit \ "CFLAGS = -DATTSV -DNOANSI -DDIRENT -DDYNAMIC -DLONGFN -DTCPSOCKET \ -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DNOSETREU \ -Dsuspend=ksuspend $(KFLAGS) -O" "LNKFLAGS =" #NeXTSTEP 1.0 through 3.2. #Includes fullscreen file transfer display (curses) and TCP/IP support. #Uses shared library to make executable program about 80K smaller. #Remove "LIBS = -lsys_s" if this causes trouble. next: @echo Making C-Kermit $(CKVER) for NeXTSTEP... @echo 'If you get errors in ckutio.c about w_S, w_T, etc,' @echo 'add KFGLAGS=-DNOREDIRECT to your make command.' $(MAKE) wermit \ "CFLAGS= -DNEXT -DNOSETBUF -DTCPSOCKET -DDYNAMIC -DLCKDIR -DKANJI \ -DCK_CURSES $(KFLAGS) -O -w" "LIBS = -lsys_s -lcurses -ltermcap" nextc: $(MAKE) "MAKE=$(MAKE)" next nextg: $(MAKE) "MAKE=$(MAKE)" next KFLAGS=-Wall nextgc: $(MAKE) "MAKE=$(MAKE)" next KFLAGS=-Wall #NeXTSTEP 3.3. #Includes fullscreen file transfer display and TCP/IP. next33: @echo Making C-Kermit $(CKVER) for NeXTSTEP 3.3... $(MAKE) wermit \ "CFLAGS= -DNEXT33 -DNOSETBUF -DTCPSOCKET -DDYNAMIC -DLCKDIR -DKANJI \ -DCK_CURSES $(KFLAGS) -O -w" "LIBS = -lsys_s -lcurses -ltermcap" #NeXT with malloc debugger nextmd: @echo Making C-Kermit $(CKVER) for NeXT with malloc debugging... $(MAKE) mermit \ "CFLAGS= -DNEXT -DNOSETBUF -DTCPSOCKET -DDYNAMIC -DLCKDIR -DKANJI \ -DCK_CURSES $(KFLAGS) -O -w -Dmalloc=dmalloc -Dfree=dfree -DMDEBUG" \ "LIBS = -lsys_s -lcurses -ltermcap" #Build for NeXTSTEP with "fat" binaries (MABs) that run on both Motorola #and Intel platforms. nextfat: $(MAKE) "MAKE=$(MAKE)" next "KFLAGS=-Wall -arch m68k -arch i386" \ "LNKFLAGS = -arch m68k -arch i386" #NeXTSTEP on Intel Platforms. next486: @echo Making C-Kermit $(CKVER) for NeXTSTEP on Intel Platforms... @echo 'If you get errors in ckutio.c about w_S, w_T, etc,' @echo 'add KFGLAGS=D-DNOREDIRECT to your make command.' $(MAKE) wermit \ "CFLAGS= -DNEXT -DNOSETBUF -DTCPSOCKET -DDYNAMIC -DLCKDIR -DKANJI \ -DNODEBUG -O3 -fno-omit-frame-pointer -fschedule-insns2 -pipe \ -DCK_CURSES $(KFLAGS) -w" "LIBS = -lsys_s -lcurses -ltermcap" #BeBox beboxdr7: @echo 'Making C-Kermit $(CKVER) for the BeBox...' @echo 'Link step will fail with default Metroworks linker 64K limit.' @echo 'Code Warrior Gold required to link big programs.' $(MAKE) wermit \ "CC=/boot/develop/tools/mwcc" "CC2=/boot/develop/tools/mwld" \ "CFLAGS= -DBEBOX -DBE_DR_7 -DPOSIX -DNOUUCP $(KFLAGS) -O" #BeBox bebox: @echo 'Making C-Kermit $(CKVER) for the BeBox...' @echo 'Link step will fail with default Metroworks linker 64K limit.' @echo 'Code Warrior Gold required to link big programs.' $(MAKE) wermit \ "CC=/boot/develop/tools/mwcc" "CC2=/boot/develop/tools/mwld" \ "CFLAGS= -DBEBOX -DPOSIX -DNOUUCP $(KFLAGS) -O" #Plan 9 from Bell Labs plan9: make -f ckpker.mk #POSIX posix: @echo 'Making C-Kermit $(CKVER) for POSIX, no UUCP lockfile support...' $(MAKE) wermit "CFLAGS= -DPOSIX -DNOUUCP $(KFLAGS) -O" #Berkeley Software Design Inc. BSDI # Substitute "LIBS= -lnewcurses -ltermcap" if desired. bsdi: @echo 'Making C-Kermit $(CKVER) for BSD/386 ...' $(MAKE) wermit \ "CFLAGS= -DBSD44 -DSETREUID -DSW_ACC_ID \ -DTCPSOCKET -DCK_CURSES -DDYNAMIC -DBPS_57K $(KFLAGS) -O" \ "LIBS= -lcurses -ltermcap" # (old name for the above) bsdiposix: $(MAKE) "MAKE=$(MAKE)" bsdi # make 386bsd 0.0new, posix # for 386bsd 0.1.24, change /usr/include/termios.h to #define NCCS if # _POSIX_SOURCE is #defined. (source: lewine, posix prgmrs guide, o`reilly) #NOTE: Lock directory is /var/spool/lock. Formerly, it was /var/spool/uucp, #but reportedly that was due to a typo in 'man tip'. 386bsd: @echo 'Making C-Kermit $(CKVER) for jolix 386BSD 0.0new and 0.1.24...' $(MAKE) wermit \ "CFLAGS= -DPOSIX -DSETREUID -DPIDSTRING -DUSLEEP \ -D_386BSD -DCK_CURSES -DTCPSOCKET -DDYNAMIC -DNOSETBUF \ -DLOCK_DIR=\\\"/var/spool/lock\\\" \ $(KFLAGS) -O" "LNKFLAGS = -s" "LIBS = -lcurses -ltermcap" freebsd: @echo 'Making C-Kermit $(CKVER) for FreeBSD 1.0 Release' $(MAKE) wermit \ "CFLAGS= -DBSD44 -DCK_CURSES -DDYNAMIC -DTCPSOCKET -DNOCOTFMC \ $(KFLAGS) -O" "LIBS= -lcurses -ltermcap" freebsd2: @echo 'Making C-Kermit $(CKVER) for FreeBSD 2.0 Release' $(MAKE) freebsd "KFLAGS=-DNDSYSERRLIST" #Pyramid 9XXX (e.g. 9845) or MIServer T series, OSx 4.4b thru 5.1 pyramid: @echo Making C-Kermit $(CKVER) for Pyramid Dual Port OSx ucb $(MAKE) wermit "CFLAGS= -DBSD43 -DTCPSOCKET -DDYNAMIC \ -DPYRAMID -O $(KFLAGS)" "LNKFLAGS = -s" #Pyramid Dual Port OSx using HonyDanBer UUCP, curses and TCP pyramid-hdb: @echo Making C-Kermit $(CKVER) for Pyramid Dual Port OSx ucb $(MAKE) wermit "CFLAGS= -DBSD43 -DTCPSOCKET -DDYNAMIC \ -DHBDUUCP -DCK_CURSES -O $(KFLAGS)" \ "LNKFLAGS = -s" "LIBS = -lcurses -ltermcap" #Pyramid DC/OSx (UNIX System V R4). #Has , regular Berkeley sockets library, i.e. in.h and inet.h #are not misplaced in sys (rather than netinet and arpa, respectively). #Uses ANSI C constructs, , etc etc. #NOTE: Remove -O and Olimit:1500 from CFLAGS if TELNET connections do not work. pyrdcosx: @echo 'Making C-Kermit $(CKVER) for Pyramid DC/OSx...' $(MAKE) wermit \ "CFLAGS = -Xa -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DCK_CURSES -DSTERMIOX -DTCPSOCKET -DPYRAMID -K Olimit:1500 \ $(KFLAGS)" "LIBS= -lcurses -lsocket -lnsl" "LNKFLAGS = -s" #SONY NEWS, NEWS-OS 4.01C sonynews: @echo Making C-Kermit $(CKVER) for SONY NEWS-OS 4.01C... $(MAKE) wermit "CFLAGS= -DBSD43 -DKANJI -DACUCNTRL \ -DTCPSOCKET -O" #SUNPOSIX #SunOS 4.1.x in the POSIX universe (but with HDB UUCP added)... sunposix: @echo Making C-Kermit $(CKVER) for POSIX... $(MAKE) wermit "CC= /usr/5bin/cc " "CC2= /usr/5bin/cc " \ "CFLAGS= -DPOSIX -DHDBUUCP -DVOID=void -O" #IBM's AIX 3.0 on IBM 370 mainframe, tested on AIX F44 thru F50. aix370: @echo Making C-Kermit $(CKVER) for IBM System/370 AIX 3.0... $(MAKE) wermit \ "CFLAGS= -DAIX370 -DTCPSOCKET -DLCKDIR -DDIRENT -DDYNAMIC $(KFLAGS)" \ "LIBS = -lbsd" #IBM's AIX/ESA 2.1 (OSF/1) on IBM mainframe aixesa: @echo Making C-Kermit $(CKVER) for IBM AIX/ESA... $(MAKE) wermit \ "CFLAGS= -DAIXESA -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" #IBM's AIX 1.3 on IBM PS/2, tested on AIX F44 thru F50. #This is exactly the same as AIX370 except for the version herald. ps2aix3: @echo Making C-Kermit $(CKVER) for IBM PS/2 AIX 3.0... $(MAKE) wermit \ "CFLAGS= -DAIXPS2 -DTCPSOCKET -DLCKDIR -DDIRENT -DDYNAMIC $(KFLAGS)" \ "LIBS = -lbsd" #IBM AIX 3.0, 3.1, or 3.2 for RISC System/6000. rs6000: @echo Making C-Kermit $(CKVER) for IBM AIX 3.0 or 3.1, RS/6000... $(MAKE) wermit \ "CFLAGS= -DAIXRS -DTCPSOCKET -DSVR3 -DDIRENT -DDYNAMIC -DCK_ANSIC \ -DCK_POLL -DNOSETBUF -DCLSOPN -DKANJI -DSELECT_H -O $(KFLAGS)" \ "LNKFLAGS = -s" #IBM AIX 3.0, 3.1, or 3.2 for RISC System/6000, with curses. rs6000c: @echo Making C-Kermit $(CKVER) for IBM AIX 3.0 or 3.1, RS/6000... $(MAKE) wermit \ "CFLAGS= -DAIXRS -DTCPSOCKET -DSVR3 -DDIRENT -DDYNAMIC -DCK_ANSIC \ -DCK_POLL -DNOSETBUF -DCLSOPN -DCK_CURSES -DKANJI -DSELECT_H \ -O $(KFLAGS)" "LIBS= -lcurses -ltermcap" "LNKFLAGS = -s" #IBM AIX 3.2 for RISC System/6000. #In case of "subprogram too complex" warnings, add "-qmaxmem=4000" to CFLAGS. rs6aix32: @echo Making C-Kermit $(CKVER) for IBM AIX 3.2, RS/6000... $(MAKE) wermit \ "CFLAGS= -DAIXRS -DTCPSOCKET -DSVR4 -DDIRENT -DDYNAMIC -DCK_ANSIC \ -DSELECT_H -DCLSOPN -DKANJI -O $(KFLAGS)" "LNKFLAGS = -s" #IBM AIX 3.2 for RISC System/6000. rs6aix32c: @echo Making C-Kermit $(CKVER) for IBM AIX 3.2, RS/6000, TCP+curses... @echo In case of Subprogram Too Complex warnings, @echo add -qmaxmem=4000 to CFLAGS. $(MAKE) wermit \ "CFLAGS= -DAIXRS -DTCPSOCKET -DSVR4 -DDIRENT -DDYNAMIC -DCK_ANSIC \ -DCLSOPN -DCK_CURSES -DKANJI -DSELECT_H -O $(KFLAGS)" \ "LNKFLAGS = -s" "LIBS=-lcurses" #IBM AIX 4.1 (Beta) or AIX 4.1.1 for RISC System/6000 or Power Series rs6aix41c: @echo Making C-Kermit $(CKVER) for IBM AIX 4.1.1 RS/6000 or PowerPC... $(MAKE) wermit \ "CFLAGS= -DAIXRS -DAIX41 -DSVR4 -DSTERMIOX -DTCPSOCKET -DDIRENT \ -DDYNAMIC -DCK_ANSIC -DCLSOPN -DCK_CURSES -DKANJI -DSELECT -DSELECT_H \ -qmaxmem=6000 -O $(KFLAGS)" "LNKFLAGS = -s" "LIBS=-lcurses" #IBM AIX 4.1 (Beta) or AIX 4.1.1 for RISC System/6000 or Power Series rs6aix41d: @echo Making C-Kermit $(CKVER) for IBM AIX 4.1.1 - debugging... $(MAKE) wermit \ "CFLAGS= -g -DAIXRS -DAIX41 -DSVR4 -DSTERMIOX -DTCPSOCKET -DDIRENT \ -DDYNAMIC -DCK_ANSIC -DCLSOPN -DCK_CURSES -DKANJI -DSELECT -DSELECT_H \ -DRLOGCODE -qcheck -qextchk -qinfo -qproto -qflag=i:i -langlvl=ansi \ -qtbtable=full -bnoquiet $(KFLAGS)" "LNKFLAGS = -s" "LIBS=-lcurses" #Bull DPX/2 with BOS/X, somewhat like AIX/RS6000 bulldpx2: @echo Making C-Kermit $(CKVER) for Bull DPX/2 with BOS/X... $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DDYNAMIC -DCK_ANSIC -DCKTYP_H= \ -DCK_POLL -DNOSETBUF -DCLSOPN -O $(KFLAGS)" "LNKFLAGS = -s" #Sun UNIX 3.5 with gcc 2.3.3. sunos3gcc: @echo Making C-Kermit $(CKVER) for Sun UNIX 3.5 and gcc... $(MAKE) wermit CC=gcc CC2=gcc \ CFLAGS="-g -O -DBSD4 -DTCPSOCKET $(KFLAGS)" #SunOS version 4.0, BSD environment, has saved original euid feature. # Add "CC=/usr/ucb/cc CC2=/usr/ucb/cc" if necessary. sunos4: @echo Making C-Kermit $(CKVER) for SunOS 4.0, BSD environment... $(MAKE) wermit \ "CFLAGS= -O -DSUNOS4 -DDIRENT -DTCPSOCKET -DSAVEDUID \ -DKANJI -DDYNAMIC $(KFLAGS)" #As above, but with SunLink X.25 support sunos4x25: @echo SunLink X.25 support $(MAKE) "MAKE=$(MAKE)" sunos4 "KFLAGS=$(KFLAGS) -DSUNX25" #SUN OS version 4.1 - 4.1.3, BSD environment, has saved original euid feature. #Uses Honey DanBer UUCP. Requires presence of /usr/spool/locks directory. # /var/spool/ should be a symbolic link to /usr/spool/. # ... or 'make wermit "CC= /usr/ucb/cc " \' sunos41: @echo Making C-Kermit $(CKVER) for SunOS 4.1 / BSD... $(MAKE) wermit "CFLAGS= -O -DSUNOS41 -DHDBUUCP -DDIRENT -DTCPSOCKET \ -DNOSETBUF -DKANJI -DSAVEDUID -DDYNAMIC -DHADDRLIST $(KFLAGS)" #As above, but compile with gcc. Gives 24-32K size reduction #with gcc 2.1 or 2.2.2. CAUTION: make sure "fixincludes" has been run on #the include files, so gcc's are in sync with the regular Sun ones! #This includes the curses library for fullscreen file transfer display. #NDGPWNAM needed for GCC 2.5.6, not needed for 2.4.0, but it's uncertain #whether it will do any harm for 2.4.0 compilation -- if so, remove it. sunos41gcc: @echo Making C-Kermit $(CKVER) for SunOS 4.1/BSD with gcc and curses... $(MAKE) wermit "CC= gcc " "CC2= gcc" \ "CFLAGS= -O -DSUNOS41 -DHDBUUCP -DDIRENT -DTCPSOCKET -DNOSETBUF \ -DNDGPWNAM -DSAVEDUID -DDYNAMIC -DKANJI -DCK_CURSES $(KFLAGS)" \ "LIBS= -lcurses -ltermcap" # Tenon MachTen, tested on Apple Powerbook with MachTen 2.1.1.D. # NOTE: This doesn't do anything about UUCP. It only works if /usr/spool/uucp # has permission of 777, and dialout device is world read/writeable. machten: @echo Making C-Kermit $(CKVER) for MachTen... $(MAKE) wermit "CFLAGS= -DBSD43 -DTCPSOCKET -DSIG_V -DNDGPWNAM \ -DCK_CURSES -O $(KFLAGS)" "LIBS=-lcurses -ltermcap" #SUNOS 4.1 as sunos41 above, but also with curses support sunos41c: @echo Curses support $(MAKE) "MAKE=$(MAKE)" sunos41 "KFLAGS=$(KFLAGS) -DCK_CURSES" \ "LIBS= -lcurses -ltermcap" #SUNOS 4.1 with SunLink X.25 support sunos41x25: @echo SunLink X.25 support $(MAKE) "MAKE=$(MAKE)" sunos41 "KFLAGS=$(KFLAGS) -DSUNX25" #SUNOS 4.1 with SunLink X.25 support and curses sunos41x25c: @echo SunLink X.25 support, curses $(MAKE) "MAKE=$(MAKE)" sunos41c "KFLAGS=$(KFLAGS) -DSUNX25" # NOTE: The sunsolxx and sunos5xx entries should no longer be necessary, but # are retained just in case. Instead, please use the solarisxx entries. #SUN with Solaris 2.0 = SunOS 5.0. #Mostly the same as System V R4. sunsol20: @echo 'Making C-Kermit $(CKVER) for Sun with Solaris 2.0 and curses...' $(MAKE) wermit "CFLAGS = -O -DSVR4 -DSOLARIS \ -DDIRENT -DHDBUUCP -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_CURSES \ -DCK_POLL $(KFLAGS)" \ "LIBS= -lsocket -lnsl -lcurses -ltermlib" "LNKFLAGS = -s" #SUN with Solaris 2.0. #As above, but built with the gcc compiler from the Cygnus CD-ROM. sunsol20gcc: @echo 'Making C-Kermit $(CKVER) for Sun Solaris 2.0, gcc, and curses..' $(MAKE) wermit "CFLAGS = -O -DSVR4 -DSOLARIS \ -DDIRENT -DHDBUUCP -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_CURSES \ -DCK_POLL $(KFLAGS)" \ "LIBS= -lsocket -lnsl -lcurses -ltermlib" "LNKFLAGS = -s" \ CC=/opt/cygnus-sol2-1.1/bin/gcc CC2=/opt/cygnus-sol2-1.1/bin/gcc #SunOS 5.1 = Solaris 2.1. #NOTE: A C compiler is no longer bundled with SunOS 5.1, so to compile C #programs, you might have to change your PATH to include the directory #/usr/ccs/bin AFTER the directory containing the compiler. SunPRO C is #installed by default in /opt/SUNWspro/bin. So a sample PATH might be: # # /usr/local/bin:/usr/bin:/opt/SUNWspro/bin:/usr/ccs/bin:\ # /usr/ucb:/usr/sbin:/sbin:. # # or: # # /usr/openwin/bin:/export/home/SUNWspro/bin:/usr/ccs/bin:/usr/sbin:/usr/bin. # #NOTE 2: Compilation with the Apogee C compiler (apcc) might not work, #because it refuses to allow "-Usun". Reportedly, newer releases of apcc #(such as 1.057) work OK, use: "make -e sunos51 CC=apcc CC2=apcc". sunos51: @echo 'Making C-Kermit $(CKVER) for SunOS 5.x....' $(MAKE) wermit \ "CFLAGS = -O -Usun -DSVR4 -DSOLARIS -DDIRENT -DHDBUUCP \ -DSELECT -DDYNAMIC -DNODEBUG -DSTERMIOX $(KFLAGS)" "LNKFLAGS = -s" #C-Kermit for Solaris 2.x compiled with gcc, includes curses and TCP/IP. #Change -O2 to -O if -O2 gives trouble. #Remove -Usun if it causes trouble. #Your PATH should start with something like: # /usr/local/gnu/bin:/usr/ccs/bin: #Produces a huge executable -- strip with /usr/ccs/bin/strip (not Gnu strip). #Also don't add "LNKFLAGS = -s" -- strip manually instead. #Also note: this can NOT be linked statically - Sun makes it impossible. #And for Solaris 2.4, you might have replace: # /usr/local/lib/gcc-lib/i486-sun-solaris2/2.4.5/include/sys/stat.h #with /usr/include/sys/stat.h. solaris2xg: @echo 'Making C-Kermit $(CKVER) for Solaris 2.x with GNU cc...' @echo 'Please read the comments that accompany this entry.' $(MAKE) wermit CC=gcc CC2=gcc \ "CFLAGS = -g -O -Usun -DSVR4 -DSOLARIS -DSTERMIOX -DSELECT \ -DCK_CURSES -DCK_NEWTERM -DDIRENT -DHDBUUCP -DDYNAMIC -DNOSETBUF \ -DTCPSOCKET -DKANJI $(KFLAGS)" \ "LIBS= -ltermlib -lsocket -lnsl" #As above with SunLink X.25 added. solaris2xg25: @echo 'Making C-Kermit $(CKVER) for Solaris 2.x + X.25 with GNU cc...' @echo 'Please read the comments that accompany the solaris2xg entry.' $(MAKE) wermit CC=gcc CC2=gcc \ "CFLAGS = -g -O -Usun -DSVR4 -DSOLARIS -DSTERMIOX -DSELECT -DSUNX25 \ -DCK_CURSES -DCK_NEWTERM -DDIRENT -DHDBUUCP -DDYNAMIC -DNOSETBUF \ -DTCPSOCKET -DKANJI $(KFLAGS)" \ "LIBS= -ltermlib -L/opt/SUNWconn/lib -R/opt/SUNWconn/lib \ -lsockx25 -lsocket -lnsl" sunos51cgcc: $(MAKE) "MAKE=$(MAKE)" solaris2xg #Solaris 2.x, SunPro compiler, includes curses and TCP/IP. #When using SUNWspro CC 2.0.1 under Solaris 2.3, be sure all cc patches #are applied, otherwise corrupt or truncated object files can result. #To build, set your PATH as follows: # /usr/local/bin:/usr/bin:/opt/SUNWspro/bin:/usr/ccs/bin:\ # /usr/ucb:/usr/sbin:/sbin:. # or (depending on where the compiler has been installed): # /usr/openwin/bin:/export/home/SUNWspro/bin:/usr/ccs/bin:/usr/sbin:/usr/bin. #For additional optimization try using "-fast -xO4 -xdepend". solaris2x: @echo 'Making C-Kermit $(CKVER) for Solaris 2.x with SunPro cc...' $(MAKE) wermit \ "CFLAGS = -O -Usun -i -DSVR4 -DDIRENT -DSOLARIS -DHDBUUCP \ -DDYNAMIC -DSELECT -DCK_CURSES -DCK_NEWTERM -DSTERMIOX -DNOSETBUF \ -DTCPSOCKET -DKANJI -DHADDRLIST $(KFLAGS)" "LNKFLAGS = -s" \ "LIBS= -ltermlib -lsocket -lnsl" #Solaris 2.x with SunLink X.25 support. #This will only run if user has /opt/SUNWconn/lib/libsockx25.so.1 #exists and can be dynamically linked. solaris2x25: @echo 'Making C-Kermit $(CKVER) for Solaris 2.x+X.25 with SunPro cc...' $(MAKE) wermit \ "CFLAGS = -O -i -Usun -DSVR4 -DSOLARIS -DDIRENT \ -DSUNX25 -DTCPSOCKET -DHADDRLIST -DHDBUUCP \ -DDYNAMIC -DSELECT -DCK_CURSES -DCK_NEWTERM -DSTERMIOX -DNOSETBUF \ -DKANJI $(KFLAGS)" "LNKFLAGS = -s" \ "LIBS= -ltermlib -L/opt/SUNWconn/lib -R/opt/SUNWconn/lib \ -lsockx25 -lsocket -lnsl" sunos51tcp: $(MAKE) "MAKE=$(MAKE)" solaris2x sunos51tcpc: $(MAKE) "MAKE=$(MAKE)" solaris2x #The following sunosxxx entries are for debugging and testing only. sunos41x: $(MAKE) wermit "CFLAGS= -O -DSUNOS41 -DDIRENT -DNOTLOG -DNOMSEND \ -DNOUUCP -DNOSIGWINCH -DNOREDIRECT -DNOPUSH -DNOCCTRAP \ -DNOSETBUF -DKANJI -DDYNAMIC -DNOICP -DNOLOCAL $(KFLAGS)" #SunOS 4.1.x, debugging with Pure Software, Inc., Purify 2 (commercial runtime #error-detection software for catching wild array references, etc). #Before running the resulting wermit, you'll also need to define and export #the following environment variables (as in this example): #PURIFYHOME=/usr/local/purify ; export PURIFYHOME #PURIFYCACHEDIR=/tmp ; export PURIFYCACHEDIR sunos41cp: @echo Making C-Kermit $(CKVER) for SunOS 4.1 / BSD / Curses / Purify... $(MAKE) wermit \ "CC2= purify -cache_dir=/usr/tmp cc" \ "CFLAGS= -g -DSUNOS41 -DHDBUUCP -DDIRENT -DTCPSOCKET -DNOSETBUF \ -DKANJI -DSAVEDUID -DDYNAMIC -DCK_CURSES $(KFLAGS)" \ "LIBS= -lcurses -ltermcap" #SunOS 4.1 with malloc debugger sunos41md: @echo Making C-Kermit $(CKVER) for SunOS 4.1 malloc debug... $(MAKE) mermit \ "CFLAGS= -O -DSUNOS41 -DHDBUUCP -DDIRENT -DTCPSOCKET \ -DSAVEDUID -DDYNAMIC $(KFLAGS) -Dmalloc=dmalloc -Dfree=dfree -DMDEBUG" sunos41gmd: @echo Making C-Kermit $(CKVER) for SunOS 4.1/BSD with gcc and curses... $(MAKE) mermit "CC= gcc " "CC2= gcc" \ "CFLAGS= -g -DSUNOS41 -DHDBUUCP -DDIRENT -DTCPSOCKET -DNOSETBUF \ -DNDGPWNAM -DSAVEDUID -DDYNAMIC -DKANJI -DCK_CURSES -DRLOGCODE \ $(KFLAGS) -Dmalloc=dmalloc -Dfree=dfree -DMDEBUG" \ "LIBS= -lcurses -ltermcap" #SunOS version 4.1, gcc, profiling with gprof, no debugging. #To get profile, "make sunos4p" (on Sun), then "./wermit". After running #wermit, "gprof ./wermit | lpr" (or whatever) to get execution profile. sunos41p: @echo Making C-Kermit $(CKVER) for SunOS 4.x with profiling... $(MAKE) wermit "CC= gcc " "CC2= gcc" \ "CFLAGS= -DSUNOS41 -DNODEBUG -DSAVEDUID -DDIRENT -DTCPSOCKET \ -DNDGPWNAM -DDYNAMIC $(KFLAGS) -pg" "LNKFLAGS = -pg" #SunOS version 4.1, BSD environment, minimum size... sunos41m: @echo Minimum size $(MAKE) "MAKE=$(MAKE)" sunos41 \ "KFLAGS=$(KFLAGS) -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG -DNOCKSPEED \ -DNOSCRIPT -DNOCSETS -DNOICP -DNOMSEND -UTCPSOCKET" \ "LNKFLAGS = -s" #SunOS version 4.1 or later, BSD environment, minimum size w/command parser. sunos41mi: @echo Minimum interactive $(MAKE) "MAKE=$(MAKE)" sunos41 \ "KFLAGS=-DNOSPL -DNOXMIT -DNOMSEND -DNOFRILLS -DNORETRY -DNOCKSPEED \ -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG -DNOSCRIPT -DNOCSETS \ -DNOSHOW -DNOSETKEY -DNOSERVER -DNOUUCP -DNORECALL -DNOREDIRECT \ -DNOSETBUF -DNOPUSH -DNOMDMHUP -DNOJC -DNOFDZERO -DNOESCSEQ \ -DNOCMDL -UTCPSOCKET $(KFLAGS)" "LNKFLAGS = -s" #SunOS 4.1, System V R3 environment (-i option omitted). sunos41s5: @echo Making C-Kermit $(CKVER) for SunOS 4.1 System V R3... @echo For testing purposes only - NOT for production use. @echo For a useable version, make sunos41 instead. $(MAKE) wermit "CC= /usr/5bin/cc " "CC2=/usr/5bin/cc " \ "CFLAGS = -DSUN4S5 -DDIRENT -DHDBUUCP -DDYNAMIC -DCK_POLL $(KFLAGS) -O" #As above, but with curses support sunos41s5c: @echo Making C-Kermit $(CKVER) for SunOS 4.1 System V R3... @echo Curses included. @echo For testing purposes only - NOT for production use. @echo For a useable version, make sunos41 instead. $(MAKE) wermit "CC= /usr/5bin/cc " "CC2=/usr/5bin/cc " \ "CFLAGS = -DSUN4S5 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DCK_POLL -DCK_CURSES -DCK_NEWTERM $(KFLAGS) -O" "LIBS= -lcurses" #As above, but with curses support AND net support sunos41s5tcpc: @echo Making C-Kermit $(CKVER) for SunOS 4.1 System V R3... @echo TCP/IP and curses included. No debug log. @echo For testing purposes only - NOT for production use. @echo For a useable version, make sunos41 instead. $(MAKE) wermit "CC= /usr/5bin/cc " "CC2=/usr/5bin/cc " \ "CFLAGS = -DSUN4S5 -DDIRENT -DHDBUUCP -DDYNAMIC -DNOSETBUF -DCK_POLL \ -DNODEBUG -DCK_CURSES -DCK_NEWTERM -DTCPSOCKET $(KFLAGS) -O" \ "LIBS= -lcurses -lresolv" # (End of SunOS test entries...) #Apollo with Domain SR10.0 or later, BSD environment #Reportedly, it might also help to add '-A,systype=bsd4.3' to CFLAGS. #Reportedly, there is also a problem with getc & putc macros that can #be handled by using '#ifdef apollo' somewhere to redefine them??? #On the other hand, other reports indicate that it works fine as-is. #NOTE: This entry was previously like this: # $(MAKE) wermit "CFLAGS= -DNOFILEH -DBSD4 $(KFLAGS) -Uaegis \ # -DTCPSOCKET -U__STDC__" #Reports (Dec 91) indicate SR10 has an ANSI-compliant C compiler, #in addition to an older one that claimed to be ANSI-compliant but wasn't. #The following make entry (plus checks that are made in ckcdeb.h) detect #which compiler is used and define the CK_ANSIC or NOANSI flags accordingly. sr10-bsd: @echo Making C-Kermit $(CKVER) for Apollo SR10.0 / BSD ... $(MAKE) wermit \ "CFLAGS= -O -DDYNAMIC -DBSD43 -DTCPSOCKET -DCK_CURSES \ -Uaegis $(KFLAGS)" "LIBS= -lcurses -ltermcap" #Apollo with Domain SR10.0 or later, System V R3 environment. #Don't use the optimizer (-O), it causes problems at runtime. sr10-s5r3: @echo Making C-Kermit $(CKVER) for Apollo SR10.0 / Sys V R3 ... $(MAKE) wermit \ "CFLAGS= -DNOFILEH -DSVR3 $(KFLAGS) -Uaegis -U__STDC__" #Apollo Domain/IX (untested, try this if sr10-bsd doesn't work) # -DTCPSOCKET -DYNAMIC can probably be added here. apollobsd: @echo Making C-Kermit $(CKVER) for Apollo Domain/IX... $(MAKE) wermit "CC= /bin/cc " "CC2= /bin/cc " \ "CFLAGS= -DNOFILEH -DBSD4 $(KFLAGS) -Uaegis" #Version 7 Unix (see comments near top of makefile) v7: @echo Making C-Kermit $(CKVER) for UNIX Version 7. @echo Read the makefile if you have trouble with this... $(MAKE) wermit "CFLAGS=-DV7 -DPROCNAME=\\\"$(PROC)\\\" \ -DBOOTNAME=\\\"$(BOOTFILE)\\\" -DNPROCNAME=\\\"$(NPROC)\\\" \ -DNPTYPE=$(NPTYPE) $(DIRECT) -DO_RDWR=2 -DO_NDELAY=0 -DO_SCCS_ID \ $(KFLAGS)" #AT&T UNIX System V R3, signal() is void rather than int. #Uses dirent.h and Honey DanBer UUCP. #Add the -i link option if necessary. #If you get errors like "ws_row undefined" in ckutio.c, add -DNONAWS. sys5r3: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R3...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS=" #As above, plus curses. sys5r3c: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R3 + curses...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DCK_CURSES $(KFLAGS) -O" \ "LNKFLAGS=" \ "LIBS = -ltermlib" iclsys5r3: make sys5r3 KFLAGS=-DICLSVR3 #AT&T UNIX System V R3. As above, but no ANSI prototyping. sys5r3na: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R3...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DNOANSI $(KFLAGS) -O" \ "LNKFLAGS=" #AT&T UNIX System V R3, for 3B computers with Wollongong TCP/IP. sys5r3net3b: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX SVR3/3B/Wollongong...' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DWOLLONGONG $(KFLAGS) \ -O" "LIBS= -lnet -lnsl_s" "LNKFLAGS =" #AT&T UNIX System V R3, signal() is void rather than int. #Uses dirent.h and Honey DanBer uucp, has . #Has for RTS/CTS flow control. sys5r3tx: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R3...' $(MAKE) wermit "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTERMIOX $(KFLAGS) -i -O" "LNKFLAGS =" #AT&T UNIX System V R3, signal() is void rather than int. #Uses dirent.h and Honey DanBer uucp, has . #Has for RTS/CTS flow control. sys5r3sx: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R3...' $(MAKE) wermit "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX $(KFLAGS) -i -O" "LNKFLAGS =" #AT&T UNIX System V R4. #Has . sys5r4: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC -DTERMIOX $(KFLAGS)" \ "LNKFLAGS = -s" #AT&T UNIX System V R4 with Wollongong TCP/IP. #Has . sys5r4net: @echo 'Making C-Kermit $(CKVER) for System V R4 + Wollongong TCP/IP...' @echo ' If sockets-library routines are missing at link time, then' @echo ' try the sys5r4net2 entry.' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTERMIOX -DWOLLONGONG $(KFLAGS)" "LNKFLAGS = -s" #As above, but needs libs included. sys5r4net2: @echo ' PLEASE READ ckuins.doc IF YOU GET MISSING HEADER FILES.' @echo ' (Search for WOLLONGONG...)' $(MAKE) sys5r4net "LIBS= -lsocket -lnsl" #As above plus curses. sys5r4net2c: echo 'Making C-Kermit $(CKVER) for System V R4 + Wollongong TCP/IP...' @echo ' PLEASE READ ckuins.doc IF YOU GET MISSING HEADER FILES.' @echo ' (Search for WOLLONGONG...)' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTERMIOX -DWOLLONGONG -DCK_CURSES $(KFLAGS)" "LNKFLAGS = -s" \ "LIBS= -lsocket -lnsl -lcurses" #DELL UNIX System V R4. #Has , regular Berkeley sockets library, i.e. in.h and inet.h #are not misplaced in sys (rather than netinet and arpa, respectively). #Uses ANSI C constructs, advisory file locking on devices, etc. #Warning: -DSTERMIOX enables hardware flow control (RTS/CTS), but reportedly #this does not work with the normal drivers. However, it might still work #on non-Dell systems, or even Dell systems with different drivers installed. dellsys5r4: @echo 'Making C-Kermit $(CKVER) for DELL UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDELL_SVR4 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DTCPSOCKET -DSTERMIOX -DCK_POLL -DKANJI $(KFLAGS)" \ "LIBS= -lsocket -lnsl" "LNKFLAGS = -s" #As above, curses support added... dellsys5r4c: @echo 'Making C-Kermit $(CKVER) for DELL UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDELL_SVR4 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DTCPSOCKET -DSTERMIOX -DKANJI -DCK_CURSES -DCK_POLL \ $(KFLAGS)" "LIBS= -lsocket -lnsl -lcurses -ltermcap" "LNKFLAGS = -s" #Mininum interactive: As above, but with every conceivable option removed. dellsys5r4mi: @echo 'Making C-Kermit $(CKVER) for DELL UNIX System V R4...' @echo 'Minimum-size interactive' $(MAKE) wermit "CFLAGS = -O -DSVR4 -DDELL_SVR4 -DDIRENT \ -DDYNAMIC -UTCPSOCKET -DNOCMDL -DNOSPL -DNOXMIT -DCK_POLL \ -DNOMSEND -DNOFRILLS -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG \ -DNOSCRIPT -DNOCSETS -DNOSHOW -DNOSETKEY -DNOSERVER -DNOUUCP \ -DNOSETBUF -DNOPUSH -DNOMDMHUP -DNOJC -DNOFDZERO -DNOESCSEQ \ $(KFLAGS)" "LNKFLAGS = -s" #Command-line only version. dellsys5r4m: @echo 'Making C-Kermit $(CKVER) for DELL UNIX System V R4...' @echo 'Command-line only' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDELL_SVR4 -DDIRENT -DDYNAMIC \ -UTCPSOCKET -DNOICP -DNOFRILLS -DNODIAL -DNODEBUG -DNOTLOG -DNOCSETS \ -DNOSETKEY -DNOESCSEQ -DNOSETBUF -DNOJC -DNOFDZERO -DCK_POLL \ $(KFLAGS)" "LNKFLAGS = -s" #AT&T UNIX System V R4. #Has . sys5r4sx: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX $(KFLAGS)" "LNKFLAGS = -s" #AT&T UNIX System V R4. #Has , regular Berkeley sockets library, i.e. in.h and inet.h #are not misplaced in sys (rather than netinet and arpa, respectively). #Uses ANSI C constructs, , etc etc. sys5r4sxtcp: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX -DTCPSOCKET $(KFLAGS)" \ "LIBS= -lsocket -lnsl" "LNKFLAGS = -s" #AT&T UNIX System V R4. #As above + curses. sys5r4sxtcpc: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX -DCK_CURSES -DTCPSOCKET $(KFLAGS)" \ "LIBS= -lsocket -lnsl -lcurses -ltermcap" "LNKFLAGS = -s" #AT&T UNIX System V R4. CONSENSYS SVR4.2-1. #Has , regular Berkeley sockets library, i.e. in.h and inet.h #are not misplaced in sys (rather than netinet and arpa, respectively). #Uses ANSI C constructs, , etc. # Fullscreen -DCK_CURSES added (with curses & termcap libs) # Submission by Robert Weiner/Programming Plus, rweiner@watsun.cc.columbia.edu sys5r4sxtcpf: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX -DTCPSOCKET -DCK_CURSES $(KFLAGS)" \ "LIBS= -lsocket -lnsl -L/usr/ccs/lib -lcurses -ltermcap" \ "LNKFLAGS = -s" #Smallest possible version for System V R4 s5r4m: @echo Minimum size $(MAKE) "MAKE=$(MAKE)" sys5r4sx \ "KFLAGS=$(KFLAGS) -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG \ -DNOSCRIPT -DNOCSETS -DNOICP -DNOMSEND -UTCPSOCKET" "LNKFLAGS = -s" #Smallest possible interactive version of above s5r4mi: @echo Minimum interactive $(MAKE) "MAKE=$(MAKE)" sys5r4sx \ "KFLAGS=-DNOSPL -DNOXMIT -DNOMSEND -DNOFRILLS -DNOSHOW \ -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG -DNOSCRIPT -DNOCSETS -DNOSETKEY \ -UTCPSOCKET $(KFLAGS)" "LNKFLAGS = -s" #AT&T UNIX System V R4, has #ANSI C function prototyping disabled. sys5r4sxna: @echo No ANSI C prototyping... $(MAKE) "MAKE=$(MAKE)" sys5r4sx "KFLAGS=$(KFLAGS) -DNOANSI" #SINIX V5.42 - includes curses, tcp/ip, everything sinix542: @echo 'Making C-Kermit $(CKVER) for Siemens/Nixdorf SINIX V5.42...' $(MAKE) wermit "CFLAGS = -DSINIX -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX -DCK_CURSES -DTCPSOCKET -DSELECT -DKANJI CK_ANSIC \ -kansi -W0 -O -KOlimit,1600 $(KFLAGS)" \ "LIBS= -lsocket -lnsl -lcurses -ltermcap" "LNKFLAGS = -s" #Commodore Amiga with AT&T UNIX System V R4 and TCP/IP support. #Has . svr4amiganet: @echo 'Making C-Kermit $(CKVER) for Amiga SVR4 + TCP/IP...' $(MAKE) wermit "CC=gcc" "CC2=gcc" \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC -DSTERMIOX \ -DTCPSOCKET -DCK_CURSES $(KFLAGS)" "LNKFLAGS = -s" \ "LIBS = -lsocket -lnsl -ltermlib" #SCO (Novell (Univel)) UnixWare 1.x or 2.x, no TCP/IP. #This assumes the Novell SDK 1.0, which has . #UnixWare users with the "Prime Time Freeware" CD-ROM SDK will probably have #to use the sys5r4 entry (no termiox.h file, so no hardware flow control). #Change -DSELECT to -DCK_POLL if -DSELECT causes problems. unixware: $(MAKE) "MAKE=$(MAKE)" sys5r4sx \ "KFLAGS=-DUNIXWARE -DSELECT $(KFLAGS)" #UnixWare 1.x or 2.x with TCP/IP and curses. unixwarenetc: $(MAKE) "MAKE=$(MAKE)" sys5r4sxtcpc \ "KFLAGS=-DUNIXWARE -DSELECT $(KFLAGS)" #No difference between 1.x and 2.x as far as Kermit is concerned. unixware2: $(MAKE) "MAKE=$(MAKE)" sys5r4sxtcpc \ "KFLAGS=-DUNIXWARE -DSELECT $(KFLAGS)" #ESIX SVR4.0.3 or 4.04 with TCP/IP support. #Has , ANSI C function prototyping disabled. #Add -m486 to CFLAGS if desired. esixr4: @echo 'Making C-Kermit $(CKVER) for ESIX SVR4 + TCP/IP...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC -DNOANSI \ -DSTERMIOX -DTCPSOCKET $(KFLAGS)" "LNKFLAGS = -s" \ "LIBS = -lsocket -lnsl" #AT&T UNIX System V R4. #Has , Wollongong WIN/TCP TCP/IP. sys5r4sxnet: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DSTERMIOX -DWOLLONGONG $(KFLAGS)" "LNKFLAGS = -s" #AT&T UNIX System V R4, no or . sys5r4nx: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC $(KFLAGS)" \ "LNKFLAGS = -s" #AT&T UNIX System V R4, no or , curses, TCP/IP. sys5r4nxnetc: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DCK_CURSES -DTCPSOCKET $(KFLAGS)" \ "LIBS = -lcurses -lsocket -lnsl -ltcpip" \ "LNKFLAGS = -s" #AT&T UNIX System V R4, no or , Wollongong TCP/IP. sys5r4nxtwg: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System V R4...' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DWOLLONGONG $(KFLAGS)" "LNKFLAGS = -s" #ICL UNIX System V R4.(DRS N/X) version :- #UNIX System V Release 4.0 ICL DRS 6000 (SPARC) #DRS/NX 6000 SVR4 Version 5 Level 1 Increment 4 #Has , regular Berkeley sockets library, i.e. in.h and inet.h #are not misplaced in sys (rather than netinet and arpa, respectively). #Uses ANSI C constructs, advisory file locking on devices, etc. iclsys5r4: @echo 'Making C-Kermit $(CKVER) for ICL UNIX System V R4 (DRS N/X)' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DICL_SVR4 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DSTERMIOX -DTCPSOCKET $(KFLAGS)" \ "LIBS= -lsocket " "LNKFLAGS = -s" #ICL UNIX System V R4.(DRS N/X) version :- #UNIX System V Release 4.0 ICL DRS 3000 (486) #DRS/NX 6000 SVR4 Version 5 Level 1 Increment 4 #As above, but also needs -lnsl. iclsys5r4_486: @echo 'Making C-Kermit $(CKVER) for ICL UNIX System V R4 (DRS N/X)' $(MAKE) wermit \ "CFLAGS = -O -DSVR4 -DICL_SVR4 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DSTERMIOX -DTCPSOCKET $(KFLAGS)" \ "LIBS= -lsocket -lnsl " "LNKFLAGS = -s" #Data General DG/UX 4.30 (System V R3) for DG AViiON, with TCP/IP support. dgux430: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 4.30...' $(MAKE) wermit \ "CFLAGS = -O -DDGUX430 -DSVR3 -DDIRENT -DDYNAMIC \ -DTCPSOCKET $(KFLAGS)" #Data General DG/UX 4.30 for DG AViiON, with TCP/IP support with BSDisms. dgux430bsd: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 4.30...' $(MAKE) wermit "CFLAGS = -O -DDGUX430 -D_BSD_SOURCE -DBSD4 \ -DDYNAMIC -DTCPSOCKET $(KFLAGS)" #Data General DG/UX 5.4 (System V R4) for DG AViiON, with TCP/IP support. dgux540: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 5.40...' $(MAKE) wermit "CFLAGS = -O -DDGUX540 -DDIRENT -DHDBUUCP \ -DKANJI -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_POLL $(KFLAGS)" dgux54: make dgux540 #DG/UX 5.4R3.00 dgux543c: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 5.4R3...' $(MAKE) wermit "CFLAGS = -O -DDGUX540 -DDGUX543 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_CURSES -DCK_POLL $(KFLAGS)" \ "LIBS= -lcurses8 -ltermcap" "LNKFLAGS = -s" #Data General DG/UX 5.4 (= System V R4) for DG AViiON, with TCP/IP support. # And curses. dgux540c: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 5.4...' $(MAKE) wermit "CFLAGS = -O -DDGUX540 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_CURSES -DCK_POLL $(KFLAGS)" \ "LIBS= -lcurses8 -ltermcap" "LNKFLAGS = -s" dgux54c: make dgux540c #Data General DG/UX 5.40 (System V R4) for Intel AViiON, with TCP/IP support. dgux540i: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 5.40...' $(MAKE) wermit "CFLAGS = -O -DDGUX540 -DDIRENT -DHDBUUCP -DNOINADDRX \ -DKANJI -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_POLL $(KFLAGS)" \ "LIBS = -lsocket -lnsl" #As above + curses. dgux540ic: @echo 'Making C-Kermit $(CKVER) for DG AViiON DG/UX 5.40...' $(MAKE) wermit "CFLAGS = -O -DDGUX540 -DDIRENT -DHDBUUCP -DNOINADDRX \ -DKANJI -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_POLL -DCK_CURSES \ $(KFLAGS)" "LIBS = -lsocket -lnsl -lcurses -ltermcap" #Silicon Graphics System V R3 with BSD file system (IRIS) iris: @echo Making C-Kermit $(CKVER) for Silicon Graphics IRIX pre-3.3... $(MAKE) wermit "CFLAGS = -O -DSVR3 -DLONGFN $(KFLAGS) \ -I/usr/include/bsd" "LIBS = -lbsd" #Silicon Graphics IRIS System V R3 irix33: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 3.3...' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS = -s" #Silicon Graphics Iris Indigo with IRIX 4.0.0 or 5.0... #Strict ANSI C compilation, TCP/IP support included irix40: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 4.0...' $(MAKE) wermit \ "CFLAGS = -DIRIX40 -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DPWID_T=uid_t \ -DCK_ANSIC -DTCPSOCKET $(KFLAGS) -O -Olimit 1500 -I/usr/include/bsd" \ "LNKFLAGS = -s" #As above, but with fullscreen display (curses) and Sun Yellow Pages support. #NOTE: IRIX versions prior to 5 run COFF binaries. irix40ypc: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 4.0.' @echo 'Includes fullscreen file display and Sun Yellow Pages...' $(MAKE) wermit \ "CFLAGS = -DIRIX40 -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DCK_CURSES \ -DPWID_T=uid_t -DCK_ANSIC -DTCPSOCKET $(KFLAGS) \ -O -Olimit 1500 -I/usr/include/bsd" \ "LIBS = -lcurses -lsun" "LNKFLAGS = -s" # Silicon Graphics Iris Series 4D/*, IRIX 4.0.x, -O4 ucode optimized. # Huge temporary file space needed for ucode optimizer. If you get an error # like "ugen: internal error writing to /tmp/ctmca08777: Error 0", define the # the TMPDIR environment variable to point to a file system that has more # space available, e.g. "setenv TMPDIR /usr/tmp". irix40u: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 4.0...' $(MAKE) wermit \ "CFLAGS = -DIRIX40 -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DPWID_T=uid_t \ -DCK_ANSIC -DTCPSOCKET $(KFLAGS) -O4 -Olimit 1500" \ "LNKFLAGS=-O4 -Olimit 1500 -s" "EXT=u" # As above, with Curses Support added irix40uc: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 4.0...' $(MAKE) wermit \ "CFLAGS = -DIRIX40 -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DPWID_T=uid_t \ -DCK_ANSIC -DCK_CURSES -DTCPSOCKET $(KFLAGS) -O4 -Olimit 1500" \ "LNKFLAGS=-O4 -Olimit 1500 -s" "EXT=u" "LIBS= -lcurses -ltermcap" #Silicon Graphics IRIX 5.x. #Yellow Pages and Curses support included. #IRIX version 5.x can run COFF or ELF binaries. irix51: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 5.x' @echo 'Includes fullscreen file display and Yellow Pages...' @echo 'Add -mips to CFLAGS specify a particular hardware target.' $(MAKE) wermit \ "CFLAGS = -DIRIX51 -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC -DCK_CURSES \ -DPWID_T=uid_t -DCK_ANSIC -DTCPSOCKET -DSELECT -DKANJI \ $(KFLAGS) -O -Olimit 1500" "LIBS = -lcurses" "LNKFLAGS = -s" irix51ypc: $(MAKE) "MAKE=$(MAKE)" irix51 #Silicon Graphics IRIX 6.0 or later. #Yellow Pages and Curses support included. #IRIX version 6.0 and later runs only ELF binaries. irix60: @echo 'Making C-Kermit $(CKVER) for Silicon Graphics IRIX 6.0' @echo 'Includes fullscreen file display and Yellow Pages...' @echo 'Add -mips to specify a particular hardware target.' $(MAKE) wermit \ "CFLAGS = -DIRIX51 -DIRIX60 -DSVR4 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DCK_CURSES -DCK_NEWTERM -DPWID_T=uid_t -DCK_ANSIC -DTCPSOCKET \ -DSELECT -DKANJI -O $(KFLAGS)" "LIBS = -lcurses" "LNKFLAGS = -s" #In case they type "make sys5"... sys5: $(MAKE) "MAKE=$(MAKE)" sys3 #Generic ATT System III or System V (with I&D space) sys3: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System III' @echo 'or System V R2 or earlier...' @echo 'add -DNOMKDIR if mkdir is an undefined symbol.' $(MAKE) wermit "CFLAGS = -DATTSV $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Generic ATT System III or System V R2 or earlier, "no void": #special entry to remove "Illegal pointer combination" warnings. sys3nv: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System III' @echo 'or System V R2 or earlier...' $(MAKE) wermit "CFLAGS = -DATTSV -Dvoid=int $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Generic ATT System III or System V (no I&D space) sys3nid: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System III' @echo 'or System V R2 or earlier, no I&D space...' $(MAKE) wermit "CFLAGS = -DATTSV $(KFLAGS) -O" "LNKFLAGS =" #AT&T 7300/UNIX PC (3B1) systems, sys3 but special handling for internal modem. #Link with the shared library -- the conflict with openi in shared library #is solved with -Dopeni=xopeni sys3upc: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC, shared lib...' @echo 'If shared lib causes trouble, use make sys3upcold.' $(MAKE) wermit \ "CFLAGS = -O -DATT7300 -DDYNAMIC -DNOSETBUF -DNOMKDIR $(KFLAGS) \ -Dopeni=xopeni" \ "CC2 = ld /lib/crt0s.o /lib/shlib.ifile" "LNKFLAGS = -s" #AT&T 7300/UNIX PC (3B1) systems, with curses support. #Curses and the shared library don't get along, so we don't use the #shared library. We need to include CK_NEWTERM to avoid a conflict #with curses and buffering on stdout. Merged with submission by #Robert Weiner/Programming Plus, rweiner@watsun.cc.columbia.edu. #We don't need -Dopeni=xopeni since we're not using the shared library, #but we keep it to be consistent with the other entries. sys3upcc: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC, curses...' $(MAKE) wermit "CFLAGS = -O -DATT7300 -DDYNAMIC -DNOSETBUF \ -DCK_CURSES -DCK_NEWTERM -DNOMKDIR $(KFLAGS) -Dopeni=xopeni" \ "LIBS = -lcurses" "LNKFLAGS = -s" #AT&T 7300 UNIX PC (3B1), as above, but no newterm(). sys3upcx: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC, curses...' $(MAKE) wermit "CFLAGS = -O -DATT7300 -DDYNAMIC -DNOSETBUF \ -DCK_CURSES -DNOMKDIR $(KFLAGS) -Dopeni=xopeni" \ "LIBS = -lcurses -ltermcap" "LNKFLAGS = -s" #AT&T 7300/UNIX PC (3B1) systems, with curses and shared library support. sys3upcshcc: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC, shared lib...' @echo 'With curses. Requires shcc.' $(MAKE) wermit "CFLAGS = -O -DATT7300 -DDYNAMIC -DNOMKDIR \ -DNOSETBUF -DCK_NEWTERM -DCK_CURSES $(KFLAGS) -Dopeni=xopeni" \ "LNKFLAGS = -i -s" "CC = shcc" "CC2 = shcc" "LIBS = -lcurses" #AT&T 7300/UNIX PC (3B1) systems, as above, no curses, but use gcc. sys3upcg: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC...' $(MAKE) wermit \ "CFLAGS = -O -DATT7300 -DDYNAMIC -DNOSETBUF -DNOMKDIR $(KFLAGS) \ -Dopeni=xopeni" \ "CC = gcc" "CC2 = gcc" "LNKFLAGS = -s -shlib" #AT&T 7300/UNIX PC (3B1) systems, curses and gcc. sys3upcgc: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC, curses...' $(MAKE) wermit "CFLAGS = -O -DATT7300 -DDYNAMIC -DNOSETBUF \ -DCK_CURSES -DIFDEBUG -DCK_NEWTERM -DNOMKDIR $(KFLAGS)" \ "CC = gcc" "CC2 = gcc" "LIBS = -lcurses" "LNKFLAGS = -s" #AT&T 7300/UNIX PC (3B1) systems, special handling for internal modem. #No FULLSCREEN file transfer display (curses). sys3upcold: @echo 'Making C-Kermit $(CKVER) for AT&T 7300 UNIX PC...' $(MAKE) wermit "CFLAGS = -DATT7300 -DNOMKDIR $(KFLAGS) -O" \ "LNKFLAGS = -i" #AT&T 7300/Unix PC systems, minimum kermit for those with smaller amounts #of memory. sys3upcm: @echo Minimum interactive $(MAKE) "MAKE=$(MAKE)" sys3upc \ "KFLAGS=-DNOSPL -DNOFRILLS -DNOHELP -DNODEBUG -DNOTLOG -DNOCSETS \ -DNOSETKEY -DNOSETBUF" #As above, but with gcc... sys3upcgm: @echo Minimum interactive $(MAKE) "MAKE=$(MAKE)" sys3upcg \ "KFLAGS=-DNOSPL -DNOFRILLS -DNOHELP -DNODEBUG -DNOTLOG -DNOCSETS \ -DNOSETKEY -DNOSETBUF" #AT&T 6300 PLUS (warning, -O might make it run out of space). #NOTE: Remove -DHDBUUCP if not using Honey DanBer UUCP. att6300: @echo 'Making C-Kermit $(CKVER) for AT&T 6300 PLUS...' $(MAKE) wermit "CFLAGS = -DATT6300 -DHDBUUCP -DNOFILEH \ $(KFLAGS) -O -Ml -i" "LNKFLAGS = -i -Ml" #As above, but with curses support. Debugging disabled to prevent thrashing. att6300c: @echo 'Making C-Kermit $(CKVER) for AT&T 6300 PLUS...' $(MAKE) wermit \ "CFLAGS = -DATT6300 -DHDBUUCP -DNOFILEH -DNOCSETS \ -DCK_CURSES -DNODEBUG $(KFLAGS) -O -Ml -i" "LNKFLAGS = -i -Ml" \ "LIBS = -lcurses" #AT&T 6300 PLUS with no curses, no debugging (about 34K smaller) # -Optimization saves about 20K too. att6300nd: @echo 'Making C-Kermit $(CKVER) for AT&T 6300 PLUS, no debugging...' $(MAKE) wermit \ "CFLAGS = -DATT6300 -DHDBUUCP -DNODEBUG -DNOFILEH $(KFLAGS) \ -O -i -Ml" "LNKFLAGS = -i -Ml" #AT&T 3B2, 3B20-series computers running AT&T UNIX System V. #This is just generic System V with Honey DanBer UUCP, so refer to sys3hdb. #Might need addition of -DNONAWS if ckutio.c compilation fails in ttgwsiz(). att3bx: $(MAKE) "MAKE=$(MAKE)" sys3hdb #AT&T 3B2, 3B20-series computers running AT&T UNIX System V, #with fullscreen file transfer display att3bxc: @echo 'Making C-Kermit $(CKVER) for AT&T 3B2 or 3B20' @echo 'with Honey DanBer UUCP and curses...' $(MAKE) wermit "CFLAGS = -DATTSV -DHDBUUCP $(KFLAGS) \ -DCK_CURSES -DCK_NEWTERM -i -O" \ "LNKFLAGS = -i" "LIBS=-lcurses" #Any System V R2 or earlier with Honey DanBer UUCP (same as above) sys3hdb: @echo 'Making C-Kermit $(CKVER) for AT&T UNIX System III' @echo 'or System V R2 or earlier with Honey DanBer UUCP...' $(MAKE) wermit "CFLAGS = -DATTSV -DHDBUUCP $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Sperry/UNISYS 5000 UTS V 5.2 (System V R2), Honey DanBer UUCP unisys5r2: @echo 'Making C-Kermit $(CKVER) for Sperry/UNISYS 5000 UTS V 5.2...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DUNISYS52 -DHDBUUCP $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #In case they say "make sys5hdb" instead of "make sys3hdb"... sys5hdb: $(MAKE) "MAKE=$(MAKE)" sys3hdb #IBM PS/2 with AIX 1.0. # Reports indicate that -O switch must be omitted. # It is also possible that "make bsd" will work (reports welcome). # One report said "make LIBS=-lbsd bsd" did the trick. ps2aix: @echo 'Making C-Kermit $(CKVER) for IBM AIX 1.0 PS/2...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DPS2AIX10 $(KFLAGS) -i" "LNKFLAGS = -i" #IBM RT PC with AIX 2.2.1 #This one has unique and strange lockfiles. rtaix: @echo 'Making C-Kermit $(CKVER) for IBM RT PC, AIX 2.2.1...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DRTAIX -DHDBUUCP -DTCPSOCKET -Wq,-SJ2 \ -DCLSOPN $(KFLAGS) -O -w" "LNKFLAGS = -s" #IBM RT PC with AIX 2.2.1 #This one has unique and strange lockfiles. rtaixc: @echo 'Making C-Kermit $(CKVER) for IBM RT PC, AIX 2.2.1, curses...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DRTAIX -DHDBUUCP -DTCPSOCKET -DCK_CURSES \ -DCLSOPN -Wq,-SJ2 $(KFLAGS) -O -w" "LIBS=-lcurses" "LNKFLAGS = -s" #IBM RT PC with AIX (ACIS) 2.2.1 (BSD 4.3) # Add -O, -DDYNAMIC, -s, etc, if they work. rtacis: @echo Making C-Kermit $(CKVER) for RT PC with ACIS 2.2.1 = BSD 4.3... $(MAKE) wermit "CFLAGS= -DBSD4 -DTCPSOCKET $(KFLAGS) -U__STDC__" \ "LNKFLAGS = -s" hpux: @echo 'Please pick a more specific HP-UX entry.' #HP 9000 series 300, 500, 800, no long filenames and no job control. #This works for HP-UX versions earlier than 6.5. #It definitely works with HP-UX 5.21. hpuxpre65: @echo 'Making C-Kermit $(CKVER) for HP-9000 HP-UX, no long filenames.' $(MAKE) wermit \ "CFLAGS = -DHPUX -DHPUXPRE65 $(KFLAGS) -O" "LNKFLAGS =" #HP-9000 500 HP-UX 5.21 with Wollongong WIN/TCP 1.2 TCP/IP #Requires /usr/wins/usr/include and /usr/lib/libnet.a from Wollongong hpux500wintcp: @echo 'Making C-Kermit $(CKVER) for HP-9000 500 HP-UX 5.21 WIN/TCP' $(MAKE) wermit \ "CFLAGS = -DHPUX -DHPUXPRE65 -DTCPSOCKET -DDYNAMIC \ -I/usr/wins/usr/include $(KFLAGS) -O" \ "LIBS = /usr/lib/libnet.a" "LNKFLAGS = " #HP 9000 series 300, 800, long filenames (using BSD file system) # (This one is probably necessary for the Series 300) hpuxlf: @echo 'Making C-Kermit $(CKVER) for HP-9000 HP-UX, long filenames...' $(MAKE) wermit \ "CFLAGS = -DHPUX -DNDIR -DLONGFN -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS =" #HP 9000 series 300, 800, long filenames (using ) hpuxde: @echo 'Making C-Kermit $(CKVER) for HP-9000 HP-UX, long filenames...' $(MAKE) wermit \ "CFLAGS = -DHPUX -DDIRENT -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS =" #HP 9000 series 300, 800, long filenames (using ) and TCP/IP hpuxdetcp: @echo 'Making C-Kermit $(CKVER) for HP-9000 HP-UX, long filenames...' $(MAKE) wermit \ "CFLAGS = -DHPUX -DDIRENT -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" \ "LNKFLAGS =" #HP 9000 series 300, 800, long filenames, System V R3 or later # (Does anybody know what is the earliest release of HP-UX based on SVR3?) hpuxs5r3: @echo 'Making C-Kermit $(CKVER) for HP-9000 HP-UX, long filenames...' $(MAKE) wermit \ "CFLAGS = -DHPUX -DSVR3 -DDIRENT -DTCPSOCKET -DDYNAMIC \ -DNOSETBUF $(KFLAGS) -O" "LNKFLAGS =" "LIBS=-lBSD" #HP-UX 6.5, short filenames, no network support. #ckcpro and ckuusr are broken out because they make the optimizer run away. hpux65: @echo 'Making C-Kermit $(CKVER) for HP-UX 6.5, no long filenames.' $(MAKE) ckcpro.$(EXT) \ "CFLAGS = -DHPUX -DDYNAMIC -DNOSETBUF -DSIG_V $(KFLAGS)" $(MAKE) ckuusr.$(EXT) \ "CFLAGS = -DHPUX -DDYNAMIC -DNOSETBUF -DSIG_V $(KFLAGS)" $(MAKE) wermit \ "CFLAGS = -DHPUX -DDYNAMIC -DNOSETBUF -DSIG_V $(KFLAGS) -O" #HP-UX 6.5, as above, plus curses: hpux65c: @echo 'Making C-Kermit $(CKVER) for HP-UX 6.5 + curses.' $(MAKE) ckcpro.$(EXT) \ "CFLAGS = -DHPUX -DDYNAMIC -DNOSETBUF -DCK_CURSES -DSIG_V $(KFLAGS)" $(MAKE) ckuusr.$(EXT) \ "CFLAGS = -DHPUX -DDYNAMIC -DNOSETBUF -DCK_CURSES -DSIG_V $(KFLAGS)" $(MAKE) wermit \ "CFLAGS = -DHPUX -DDYNAMIC -DNOSETBUF -DCK_CURSES -DSIG_V $(KFLAGS) \ -O" "LIBS= -lcurses -ltermcap" #HP-UX 7.0, no long filenames, no network support. hpux7sf: @echo 'Making C-Kermit $(CKVER) for HP-9000 HP-UX, no long filenames.' $(MAKE) ckcpro.$(EXT) \ "CFLAGS = -DHPUX $(KFLAGS) -DSIG_V" $(MAKE) wermit \ "CFLAGS = -DHPUX $(KFLAGS) -DSIG_V -O" "LNKFLAGS =" #HP-UX 7.0, short filenames, but with tcp/ip and curses. #There must be & present to support this #configuration. To use this, you must have bought the ARPA Services #Product from HP, and you must get the files "telnet.h" and "inet.h" #from the Berkeley Standard Distribution because (reportedly) they are not #part of the HP product. And you need /usr/lib/libBSD.a. hpux70sftcpc: @echo 'Making C-Kermit $(CKVER) for HP9000/8xx HP-UX V. 7.0' @echo 'supporting: NO long filenames, networking, curses, HDB uucp...' $(MAKE) ckcpro.$(EXT) \ "CFLAGS = -DHPUXDEBUG -DHPUX -DSVR3 -DCK_REDIR -DDYNAMIC -DNOSETBUF \ -DTCPSOCKET -DCK_CURSES $(KFLAGS)" $(MAKE) wermit \ "CFLAGS = -DHPUXDEBUG -DHPUX -DSVR3 -DCK_REDIR -DDYNAMIC -DNOSETBUF \ -DHDBUUCP -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DCK_RTSCTS \ -DTCPSOCKET -DCK_CURSES $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS= -lcurses -ltermcap -lBSD" #HP 9000 series 800 HP-UX 7.0, long filenames, network support, HDB uucp. #See comments in hpux70sftcpc about TCP/IP support. hpux70lfn: @echo 'Making C-Kermit $(CKVER) for HP9000/8xx HP-UX V. 7.0' @echo 'supporting: long filenames, networking, HDB uucp...' $(MAKE) ckcpro.$(EXT) \ "CFLAGS = -DHPUXDEBUG -DHPUX -DSVR3 -DDYNAMIC -DNOSETBUF \ -DCK_REDIR -DCK_RTSCTS -DTCPSOCKET $(KFLAGS)" $(MAKE) wermit \ "CFLAGS = -DHPUXDEBUG -DHPUX -DSVR3 -DDYNAMIC -DNOSETBUF \ -DHDBUUCP -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DDIRENT -DLONGFN \ -DCK_REDIR -DCK_RTSCTS -DTCPSOCKET $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS = -lBSD" hpux70lfnc: @echo 'Making C-Kermit $(CKVER) for HP9000/8xx HP-UX V. 7.0' @echo 'supporting: curses, long filenames, networking, HDB UUCP...' $(MAKE) ckcpro.$(EXT) \ "CFLAGS = -DHPUXDEBUG -DHPUX -DSVR3 -DDIRENT -DLONGFN \ -DDYNAMIC -DNOSETBUF -DCK_REDIR -DTCPSOCKET -DCK_CURSES $(KFLAGS)" $(MAKE) wermit \ "CFLAGS = -DHPUXDEBUG -DHPUX -DSVR3 -DDIRENT -DLONGFN \ -DHDBUUCP -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DCK_RTSCTS \ -DDYNAMIC -DNOSETBUF -DCK_REDIR -DTCPSOCKET -DCK_CURSES $(KFLAGS) -O" \ "LIBS= -lcurses -ltermcap -lBSD" "LNKFLAGS = -s" #HP 9000 Series 300 or 400, HP-UX 8.0, long filenames and TCP/IP support. #This one should also work on 700/800, but without PA-specific optimization. #In case -DCK_RTSCTS and -DCK_REDIR make trouble, remove them. #NOTE: ckcpro.c blows up the optimizer, so don't optimize it. For HP-UX 8.0 #on Motorola CPUs, you might have to reinstall your kernel with maxdsiz >= #0x02000000. But if physical memory is small, that still will not help much. hpux80: @echo 'Making C-Kermit $(CKVER) for HP9000 HP-UX V. 8.0' @echo 'supporting: long filenames, TCP/IP, HDB UUCP...' $(MAKE) -B "CC=$(CC)" "CC2=$(CC2)" ckcpro.$(EXT) \ "CFLAGS = -DCK_REDIR -DHPUXDEBUG -DHPUX -DHPUX8 -DSVR3 -DRENAME \ -DDYNAMIC -DTCPSOCKET $(KFLAGS)" $(MAKE) -B "CC=$(CC)" "CC2=$(CC2)" wermit \ "CFLAGS = -DCK_REDIR -DHPUXDEBUG -DHPUX -DHPUX8 -DSVR3 -DRENAME \ -DDIRENT -DLONGFN -DCK_RTSCTS \ -DHDBUUCP -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DNOSETBUF \ -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS = -lBSD" #Exactly as above + curses. hpux80c: @echo 'Making C-Kermit $(CKVER) for HP9000 HP-UX V. 8.0' @echo 'supporting: long filenames, TCP/IP, HDB UUCP, curses...' $(MAKE) -B "CC=$(CC)" "CC2=$(CC2)" ckcpro.$(EXT) \ "CFLAGS = -DCK_REDIR -DHPUXDEBUG -DHPUX -DHPUX8 -DSVR3 -DRENAME \ -DDYNAMIC -DTCPSOCKET $(KFLAGS)" $(MAKE) -B "CC=$(CC)" "CC2=$(CC2)" wermit \ "CFLAGS = -DCK_REDIR -DHPUXDEBUG -DHPUX -DHPUX8 -DSVR3 -DRENAME \ -DDIRENT -DLONGFN -DCK_RTSCTS -DCK_CURSES \ -DHDBUUCP -DLOCK_DIR=\\\"/usr/spool/uucp\\\" -DNOSETBUF \ -DDYNAMIC -DTCPSOCKET $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS = -lBSD -lcurses" #HP 9000 Series 700 or 800, HP-UX 8.0, long filenames and TCP/IP support. # Like the previous entries, but with PA-specific optimization. hpux80pa: $(MAKE) hpux80 "KFLAGS = $(KFLAGS) +Obb1100" #As above, but with curses. hpux80pac: $(MAKE) hpux80c "KFLAGS = $(KFLAGS) +Obb1100" #As above, but compiled with GCC 2.3.3. hpux80pagcc: @echo 'Making C-Kermit $(CKVER) for HP9000 HP-UX 8.0 with gcc,' @echo 'supporting: long filenames, networking, HDB uucp...' $(MAKE) "CC=gcc" "CC2=gcc" hpux80 #HP 9000 HP-UX 8.0, no TCP/IP because /usr/lib/libBSD.a can't be found, #or TCP/IP header files missing. hpux80notcp: $(MAKE) "MAKE=$(MAKE)" hpux80 "KFLAGS = $(KFLAGS) -UTCPSOCKET" #HP-UX 9.0, 9.01, 9.03, 9.04, 9.05, 9.07, 9.10 ..., + TCP/IP + curses, fully #configured. Use this entry with the restricted compiler: no optimization, no #ANSI support. If you get unresolved sockets library references at link time, #then try adding -lBSD to LIBS, or else remove -DTCPSOCKET to build a version #without TCP/IP support. hpux90: @echo 'Making C-Kermit $(CKVER) for HP9000 HP-UX V. 9.0...' @echo 'Read comments in the hpux90 entry if you have trouble.' $(MAKE) wermit "CFLAGS = -DHPUX9 -DDIRENT -DHPUXDEBUG -DLONGFN \ -DTCPSOCKET -DCK_CURSES -DHDBUUCP -DDYNAMIC -DNOSETBUF -DKANJI \ -DSTERMIOX -DCK_REDIR -DRENAME \ -DLOCK_DIR=\\\"/usr/spool/uucp\\\" $(KFLAGS)" \ "LNKFLAGS = -s" "LIBS = -lcurses" "CC=$(CC)" "CC2=$(CC2)" #Like hpux90, but for the "value-added" compiler on all HP 9000 models. #Adds optimization and ANSI compilation: # +O2 makes smaller executable (= -O = Level-1 and global optimization) # +O3 adds interprocedural global optimization, makes bigger executable. # If optimization fails on some modules, you can add: # +Obb, +Olimit , or +Onolimit, depending on your cc version, # where is a number, e.g. +Obb1200. In other words, if you get optimizer # warnings, add (for example) +Obb1200; if you still get optimizer warnings, # increase the number. Repeat until warnings go away. If your compiler # permits it, use +Onolimit. If optimizer blows up on ckcpro.c, see next entry. # Reportedly, on some configurations, such as HP9000/425e or /340, perhaps # depending on the amount of main memory, this entry might fail no matter what # you do ("Out of Memory", "cc: Fatal error in /lib/c.c1", etc). In that case # use "make hpux90" (no "o"). hpux90o: $(MAKE) hpux90 \ "KFLAGS = $(KFLAGS) -Aa -DCK_ANSIC -D_HPUX_SOURCE +O2" # For HP-UX 9.0 on Motorola CPUs, optimization of ckcpro.c tends to blow up # the compiler. You might have to reinstall your kernel with maxdsiz >= # 0x03000000. But if physical memory is small, that still will not help much. # In that case, use this entry to skip optimization of ckcpro.c. hpux90mot: $(MAKE) ckcpro.$(EXT) "CFLAGS = -DHPUX9 -DHPUXDEBUG \ -DTCPSOCKET -DDYNAMIC -DCK_REDIR -DRENAME $(KFLAGS)" $(MAKE) hpux90 \ "KFLAGS = $(KFLAGS) -Aa -DCK_ANSIC -D_HPUX_SOURCE +O2" #Like hpux90o but with additional model-700/800-specific optimizations. # +ESlit = consolidate strings in read-only memory. # +ESfsc = inline millicode calls when comparing pointers. hpux90o700: @echo 'If you get optimizer warnings' @echo 'Try "make hpux90o700 KFLAGS=+Obb1200"' $(MAKE) hpux90o "KFLAGS = $(KFLAGS) +ESlit +ESsfc" #HP-UX 9.0, 9.01, 9.03, 9.04, ..., + TCP/IP + curses, fully configured, #built with gcc, all models except 800 series. hpux90gcc: $(MAKE) hpux90 CC=gcc CC2=gcc \ "KFLAGS = $(KFLAGS) -DCK_ANSIC -O2" #HP-9000 HP-UX 10.0 + TCP/IP + curses, fully configured. #Use with restricted (bundled) compiler: no optimization, no ANSI support. #libcurses needed for fullscreen file xfer display in HP-UX 10.00 and 10.01. #libHcurses (NOT libcurses!) for fullscreen display, to work around fatal bugs #in HP-UX 10.10 and 10.20 curses. Maybe we could use lcurses for 10.30, since #the 10.10 curses problem is supposedly fixed in 10.30. hpux100: @echo 'Making C-Kermit $(CKVER) for HP9000 HP-UX V.10.xx...' @touch ckuker.cpp $(MAKE) "SHELL=/usr/bin/sh" "CFLAGS=-DHPUX10" manpage @case `uname -r` in \ [AB].10.0*) KFLAGS='-DHPUX1000 $(KFLAGS)' ; \ LIBS=' -lcurses' ;; \ [AB].10.1*) KFLAGS='-DHPUX1010 -D__HP_CURSES $(KFLAGS)' ; \ LIBS=' -lHcurses' ;; \ [AB].10.2*) KFLAGS='-DHPUX1020 -D__HP_CURSES $(KFLAGS)' ; \ LIBS=' -lHcurses' ;; \ [AB].10.3*) KFLAGS='-DHPUX1030 -D__HP_CURSES $(KFLAGS)' ; \ LIBS=' -lHcurses' ;; \ [AB].10.?*) KFLAGS='-DHPUX10XX -D__HP_CURSES $(KFLAGS)' ; \ LIBS=' -lHcurses' ;; \ esac ; \ $(MAKE) "SHELL=/usr/bin/sh" wermit \ "CFLAGS = -DHPUX10 -DDIRENT -DSTERMIOX -DCK_DSYSINI -DHDBUUCP \ -DCK_CURSES -DCK_WREFRESH -DKANJI -DDYNAMIC -DNOSETBUF \ -DTCPSOCKET -DCK_REDIR -DRENAME $$KFLAGS" \ "LNKFLAGS=-s $(LNKFLAGS)" "LIBS = $$LIBS" #HP-9000 HP-UX 10.00 and higher with ANSI prototyping and optimization. #PA-RISC only, no Motorola or other hardware is support in HP-UX 10.00++. #The unbundled optional compiler is required. #Your path should start with /opt/ansic/bin. # -Wl,-Fw = Remove stack unwind table (info used by debuggers). # +O2 makes a smaller executable (= -O = Level-1 and global optimization). # +O3 adds interprocedural global optimization, makes a bigger executable. # +Onolimit allows all modules to be optimized, no matter how complex. But: # (a) +Onolimit does not seem to always be there in HP-UX 10.00, and: # (b) some modules might take hours on low-memory and/or slow systems. # The following are PA-RISC-specific optimizations: # +ESlit = Consolidate strings in read-only memory. # +ESfsc = Inline millicode calls when comparing pointers. # +DA1.0 = Generate code that runs on both 700 and 800 models. # You might need to configure your kernel for a maxdsiz of 0x06000000 (96MB) # or greater to prevent the optimizer from running out of space. hpux100o: $(MAKE) "SHELL=/usr/bin/sh" "PATH=/opt/ansic/bin:$$PATH" hpux100 \ "KFLAGS = $(KFLAGS) \ -Aa -D_HPUX_SOURCE -DCK_ANSIC -DUTIMEH \ +O2 -Wl,-Fw +ESlit +ESsfc +DA1.0" #The same like hpux100o but with "+Onolimit" hpux100o+: $(MAKE) hpux100o \ "KFLAGS = $(KFLAGS) +Onolimit" #Regulus on CIE Systems 680/20 cie: @echo 'Making C-Kermit $(CKVER) for CIE Systems 680/20 Regulus...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DNOFILEH -DCIE $(KFLAGS) -O" "LNKFLAGS =" # Linux 0.99.14 or later with gcc, dynamic libraries, curses, TCP/IP. # # -DLINUXFSSTND (Linux File System Standard) gives UUCP lockfil /var/lock with # string pid. Remove this and get /usr/spool/uucp with int pid, which was used # in early Linux versions. # # If you get compiler errors regarding , add -DNOHISPEED. # # -DCK_POSIX_SIG (POSIX signal handling) is good for Linux releases back to at # least 0.99.14; if it causes trouble for you, just remove it. # # -DCK_CURSES: Here we link with the regular curses library. But you should # be using ncurses. Internally, the ckuusx.c module includes , but # this really should be . Thus if you have the new curses # material, you should either install it with the standard names, or else # create symbolic links from the standard names to the new ones. If you get # compile-time errors complaining about data definitions in termcap.h, it # means you have new kernel material mixed with older libc header files. To # fix, add "#include " to the file. Or if all this is # too confusing, create a new makefile entry based on this one, but with # -DCK_CURSES removed from CFLAGS and the entire LIBS= clause removed. # # But wait, there's more. On most Linux systems, -ltermcap must be included # in LIBS. But on others, the linker complains that libtermcap can't be # found. In that case, try removing -ltermcap from LIBS=. # # But wait, there's more. The format of the PID string in the UUCP lockfile # changed between Linux FSSTND 1.0 and 1.2. In the earlier standard, it had # leading zeros; in the second, it has leading spaces. By default this entry # uses the newer standard. To force the second one, add -DFSSTND10. # # "The nice thing about the Linux standard is there are so many to choose from" # # NOTE: Remove -DBIGBUFOK for small-memory or limited-resource systems. linux: @echo 'Making C-Kermit $(CKVER) for Linux...' @echo 'IMPORTANT: Read the comments in the linux section of the' @echo 'makefile if you get compilation or link errors.' $(MAKE) wermit "CC = gcc" "CC2 = gcc" \ "CFLAGS = -O -DPOSIX -DDYNAMIC -DCK_CURSES -DCK_POSIX_SIG \ -DBIGBUFOK -DTCPSOCKET -DLINUXFSSTND $(KFLAGS)" \ "LNKFLAGS = $(LNKFLAGS)" "LIBS = -lcurses -ltermcap" #This version was used for Linux prior to C-Kermit 6.0.192. #Now the "Linux File System Standard" is considered standard, ditto TCP/IP. linuxold: @echo 'Making C-Kermit $(CKVER) for Linux...' @echo 'For FSSTND-recommended UUCP lockfiles, use:' @echo ' make linux "KFLAGS=-DLINUXFSSTND".' @echo 'Use "make linuxtcp" to add TCP/IP support.' @echo 'Read comments in makefile for additional options.' $(MAKE) wermit "CC = gcc" "CC2 = gcc" \ "CFLAGS = -O -DPOSIX -DDYNAMIC -DCK_CURSES -DCK_POSIX_SIG \ $(KFLAGS)" "LNKFLAGS = $(LNKFLAGS)" "LIBS = -lcurses -ltermcap" # "make linux", but with static linking to avoid confusion with DLL versions. # Use this to make a portable binary. Adds about 100K to the executable. linuxs: $(MAKE) linux "KFLAGS = $(KFLAGS)" "LNKFLAGS = -static" linuxnotcp: $(MAKE) linux "KFLAGS = -DNONET $(KFLAGS)" # "make linuxnotcp" with lcc (see http://www.cs.princeton.edu/software/lcc) # lcc does not understand various gcc extensions: # "__inline__" -- can be eliminated by adding "-D__inline__=" # "__asm__ and "long long" -- in header files, should be surrounded by # "#ifndef(__STRICT_ANSI__)"/"#endif" # however, TCP requires some __asm__ functions, so cannot be compiled linuxnotcp-lcc: @echo 'Making C-Kermit $(CKVER) for Linux with lcc ...' @echo 'Read comments in makefile for additional information.' $(MAKE) wermit "CC = lcc" "CC2 = lcc" \ "CFLAGS = -DPOSIX -DDYNAMIC -DCK_CURSES -DCK_POSIX_SIG \ -UTCPSOCKET -DLINUXFSSTND $(KFLAGS)" \ "LNKFLAGS = $(LNKFLAGS)" "LIBS = -lcurses -ltermcap" # LynxOS 2.2 with GCC compiler, TCP/IP and fullscreen display. # Probably also works with Lynx 2.1, and maybe even Lynx 2.0. # -X means use termios serial drivers rather than BSD4.3-style sgtty drivers. # If you have trouble with this, try "make bsd KFLAGS=-DNOFDZERO". lynx: @echo 'Making C-Kermit $(CKVER) for LynxOS 2.2 with TCP/IP' $(MAKE) wermit "CC = gcc" "CC2 = gcc" \ "CFLAGS= -O -DPOSIX -DDIRENT -DSETREUID -DCK_CURSES -DTCPSOCKET \ -DCK_ANSIC -DLYNXOS" "LNKFLAGS = -X" "LIBS = -lcurses -lbsd" lynx22: $(MAKE) lynx "KFLAGS=$(KFLAGS)" # LynxOS 2.1 with GCC compiler 1.40 and TCP/IP. lynx21: @echo 'Making C-Kermit $(CKVER) for LynxOS 2.1 with TCP/IP' $(MAKE) kermit "CC = gcc" "CC2 = gcc" \ "CFLAGS= -O -DSETREUID -DTCPSOCKET -DCK_ANSIC -DBSD4 -DLYNXOS" \ "LIBS = -lbsd" #Microport SV/AT for IBM PC/AT 286 and clones, System V R2. #The -O flag may fail on some modules (like ckuus2.c), in which case you #should compile them by hand, omitting the -O. If you get "hash table #overflow", try adding -DNODEBUG. #Also, reportedly this compiles better with gcc than with cc. mpsysv: @echo 'Making C-Kermit $(CKVER) for Microport SV/AT 286...' $(MAKE) wermit \ "CFLAGS= -DATTSV $(KFLAGS) -O -Ml" "LNKFLAGS = -Ml" #Microsoft "Xenix/286" e.g. for IBM PC/AT xenix: @echo 'Making C-Kermit $(CKVER) for Xenix/286' $(MAKE) wermit \ "CFLAGS= -DXENIX -DNOFILEH $(KFLAGS) -Dunix -F 3000 -i" \ "LNKFLAGS = -F 3000 -i" #SCO Xenix 2.2.1 for IBM PC, XT, PS2/30, or other 8088 or 8086 machine #Should this not work, try some of the tricks from sco286. #NOTE: -DRENAME is omitted for early SCO Xenix releases because it didn't #exist, or its semantics were different from the later POSIX-compliant #version of rename(). sco86: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/86...' $(MAKE) wermit \ "CFLAGS= -DXENIX -DNOFILEH $(KFLAGS) -Dunix -F 3000 -i -M0me" \ "LNKFLAGS = -F 3000 -i -s -M0me" "LIBS = -lx" #SCO Xenix/286 2.2.1, e.g. for IBM PC/AT, PS/2 Model 50, etc. #Reportedly, this "make" can fail simply because of the size of this #makefile. If that happens, use "makeL", or edit out some of the #other entries. No debugging or character-set translation. sco286: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/286...' @echo 'If make fails, try using makeL.' $(MAKE) wermit \ "CFLAGS= -s -O -LARGE -DXENIX -DNOFILEH -Dunix -DRDCHK -DNAP \ -DNODEBUG -DNOTLOG -DNOCSETS \ $(KFLAGS) -F 3000 -i -M2let32" \ "LIBS = -lx" "LNKFLAGS = -s -O -LARGE -F 3000 -i -M2let32" #SCO Xenix/286 2.2.1, e.g. for IBM PC/AT, PS/2 Model 50, etc. #As above, but with HDBUUCP sco286hdb: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/286 with HDB UUCP...' @echo 'If make fails, try using makeL.' $(MAKE) wermit \ "CFLAGS= -s -O -LARGE -DXENIX -DNOFILEH -Dunix -DRDCHK -DNAP \ -DHDBUUCP $(KFLAGS) -F 3000 -i -M2let32" \ "LIBS = -lx" "LNKFLAGS = -s -O -LARGE -F 3000 -i -M2let32" #SCO Xenix/386 2.2.2 and 2.2.3 sco386: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/386 2.2.2...' $(MAKE) wermit \ "CFLAGS= -DXENIX -DNOFILEH -Dunix -DRDCHK -DNAP $(KFLAGS) -Otcl -M3e" \ "LNKFLAGS = -s" "LIBS = -lx" #SCO XENIX/386 2.2.3 with Excelan TCP/IP + curses. # NOTE: This one might need some work in C-Kermit 6.0. # You might need to include /usr/include/sys/types.h # containing "typedef char *caddr_t;". Then at least it compiles, but the # stack sco386netc: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/386 2.2.3 + Excelan TCP' $(MAKE) wermit \ "CFLAGS= -I/usr/include/exos -DXENIX -DNOFILEH -DCK_CURSES -DDYNAMIC \ -Dunix -DRDCHK -DNAP -DTCPSOCKET -DEXCELAN -DNOJC -DNOMKDIR \ $(KFLAGS) -Otcl -M3e" \ "LNKFLAGS = -s" "LIBS = -lc -lx -lsocket -lcurses -ltermcap" #SCO XENIX/386 2.3.3 with gcc 1.37 or later... sco386gcc: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/386 2.3.3, gcc...' @echo 'Add -D_NO_PROTOTYPE if you have trouble with Xenix header files' $(MAKE) wermit "CC = gcc" "CC2 = gcc" \ "CFLAGS= -O -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP \ -DNOJC -DNODEBUG -DDYNAMIC $(KFLAGS) \ -traditional -fpcc-struct-return -fstrength-reduce \ -DM_BITFIELDS -DM_COFF -DM_I386 -DM_I86 -DM_I86SM \ -DM_INTERNAT -DM_SDATA -DM_STEXT -DM_SYS3 -DM_SYS5 \ -DM_SYSIII -DM_SYSV -DM_WORDSWAP -DM_XENIX \ -DPWID_T=int " "LNKFLAGS = -s" "LIBS = -lx" #As above, but with curses... sco386gccc: @echo 'Making C-Kermit $(CKVER) for SCO Xenix/386 2.3.3, gcc...' @echo 'Add -D_NO_PROTOTYPE if you have trouble with Xenix header files' $(MAKE) wermit "CC = gcc" "CC2 = gcc" \ "CFLAGS= -O -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP \ -DNOJC -DNODEBUG -DDYNAMIC -DCK_CURSES $(KFLAGS) \ -traditional -fpcc-struct-return -fstrength-reduce \ -DM_BITFIELDS -DM_COFF -DM_I386 -DM_I86 -DM_I86SM \ -DM_INTERNAT -DM_SDATA -DM_STEXT -DM_SYS3 -DM_SYS5 \ -DM_SYSIII -DM_SYSV -DM_WORDSWAP -DM_XENIX \ -DPWID_T=int " "LNKFLAGS = -s" "LIBS = -lx -lcurses -ltermlib" #SCO UNIX (and ODT) entries... # #NOTE: All SCO UNIX entry LIBS should have "-lc_s -lc -lx" IN THAT ORDER (if #shared C library is desired), or else "-lc -lx" IN THAT ORDER. Use shared C #libraries to save memory, but then don't expect to run the resulting binary #on a different machine. When using -lc_s, you must also use -lc, because the #shared C library does not contain all of libc.a. And in all cases, -lc must #ALWAYS precede -lx. # #ANOTHER NOTE: -DRENAME is included in all SCO UNIX entries. Remove it if it #causes trouble. No harm is done by removing it (see ckuins.doc). # #AND ANOTHER: In theory, it should be possible to run SCO UNIX binaries on #SCO Xenix 2.3 and later. In practice, this might not work because of the #libraries, etc. Also, don't add the -link -z switch (which is supposed to #root out references to null pointers) because it makes UNIX binaries core #dump when they are run under Xenix. #NOTE: -Otcl removed and replaced by -O, since -Otcl produced incorrect code. #SCO UNIX/386 3.2.0, 3.2.1, and SCO Xenix 2.3.x sco3r2: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2.0 or 3.2.1 ...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following three continued lines into one line.' @echo 'Also, remove -DRENAME if _rename unresolved at link time.' $(MAKE) wermit \ "CFLAGS= -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP \ -DRENAME -DNOJC $(KFLAGS) -O" "LNKFLAGS = -s" "LIBS = -lc -lx" # Exactly the same as above, but enables some special SCO-specific code # that allegedly clears up some problems with HANGUP and with uugetty. # For satisfactory operation on bidirectional lines that are handled by # uugetty, you must install the kermit program with owner=group=uucp # and permission 06755. sco3r2x: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following four continued lines into one line.' @echo 'Also, remove -DRENAME if _rename unresolved at link time.' $(MAKE) wermit \ "CFLAGS= -DSCO32 -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP \ -DNOJC -DRENAME -DNOCOTFMC $(KFLAGS) -Otcl" \ "LNKFLAGS = -s" "LIBS = -lc -lx" #SCO UNIX/386 3.2.0 and SCO Xenix 2.3.x with Excelan TCP/IP support. #In case of compilation or runtime problems, try adding #"-DUID_T=int -DGID_T=int" to the CFLAGS. If that doesn't work, try #"-DUID_T=uid_t -DGID_T=gid_t". sco3r2net: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 / Excelan...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following three continued lines into one line.' $(MAKE) wermit \ "CFLAGS= -I/usr/include/exos -DXENIX -DSVR3 -DDYNAMIC -DNOFILEH \ -DHDBUUCP -DRDCHK -DNAP -DRENAME -DTCPSOCKET -DEXCELAN -DNOJC \ $(KFLAGS) -O" "LNKFLAGS = -s" "LIBS = -lc -lx -lsocket" #SCO UNIX/386 3.2.0 and SCO Xenix 2.3.x with Excelan TCP/IP support. #As above, with curses library added for FULLSCREEN file transfer display. #See comments for sco3r2net. sco3r2netc: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 / Excelan / curses...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following three continued lines into one line.' $(MAKE) wermit \ "CFLAGS= -I/usr/include/exos -DXENIX -DSVR3 -DDYNAMIC -DNOFILEH \ -DHDBUUCP -DRDCHK -DNAP -DTCPSOCKET -DEXCELAN -DNOJC $(KFLAGS) \ -DRENAME -DCK_CURSES -O" "LNKFLAGS = -s" \ "LIBS = -lc -lx -lsocket -lcurses -ltermcap" #SCO UNIX 3.2.x or SCO Xenix 2.3.x with Racal InterLan TCP/IP support # Extra compile flags for other version of Racal InterLan TCP/IP: # Xenix286/NP621-286, use -Ml -DPARAMH -DINTERLAN -Di286 -DSYSV # Xenix386/NP621-386, use -DPARAMH -DINTERLAN -Di386 -DSYSV # ISC386ix/NP622I, use -DSYSV -Di386 # SCO Unix3.2/NP622S, use -DSYSV -Di386 -DSCO_UNIX # AT&T SVR3.2/NP622A, use -DSYSV -Di386 -DATT sco3r2netri: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 / Racal InterLan...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following five continued lines into one line.' $(MAKE) wermit \ "CFLAGS= -I/usr/include/interlan -DXENIX -DNOFILEH -DHDBUUCP \ -DSVR3 -DRDCHK -DNAP -DTCPSOCKET -DPARAMH -DINTERLAN -Di386 -DSYSV \ -DRENAME -DNOJC $(KFLAGS) -Otcl -M3e" "LNKFLAGS = -s" \ "LIBS = -lc -lx -ltcp" # SCO XENIX/386 2.3.3 SysV with SCO TCP/IP # System V STREAMS TCP developed by Lachman Associates Inc and # Convergent Technologies. # -DRENAME removed since some reports indicate it is not supported # (whereas others say it is.) sco3r2lai: @echo 'Making C-Kermit $(CKVER) for SCO XENIX/386 2.3.3 + TCP/IP...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following four continued lines into one line.' $(MAKE) wermit \ "CFLAGS= -DLAI_TCP -Di386 -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK \ -DNAP -DTCPSOCKET -DPWID_T=int $(KFLAGS) -Otcl -i -M3e" \ "LNKFLAGS = -i -s" "LIBS = -lc -lx -lsocket" sco3r2laic: @echo 'Making C-Kermit $(CKVER) for SCO XENIX/386 2.3.3 + TCP/IP...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following five continued lines into one line.' $(MAKE) wermit \ "CFLAGS= -DLAI_TCP -Di386 -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK \ -DNAP -DTCPSOCKET -DDYNAMIC -DCK_ANSIC -DCK_CURSES -DM_TERMINFO \ -DPWID_T=int $(KFLAGS) -Otcl -i -M3e" \ "LNKFLAGS = -i -s" "LIBS = -ltinfo -lc -lx -lsocket" #SCO UNIX/386 3.2v2 (POSIX job control), shared libraries. sco3r22: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2v2 ...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following three continued lines into one line.' make wermit \ "CFLAGS= -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP -DRENAME \ -DPID_T=pid_t -DPWID_T=int -DDIRENT -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS = -lc_s -lc -lx" #SCO UNIX/386 3.2v2, POSIX job control, fullscreen file transfer display, #dynamic memory allocation, shared C library sco3r22c: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2v2 ...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following four continued lines into one line.' make wermit \ "CFLAGS= -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP \ -DCK_CURSES -DDYNAMIC -DDIRENT -DRENAME \ -DPID_T=pid_t -DPWID_T=int $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS = -lcurses -lc_s -lc -lx" #SCO UNIX/386 3.2v2 with gcc 1.40 or later (POSIX job control) sco3r22gcc: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2v2, gcc' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following seven continued lines into one line.' make wermit "CC = gcc" \ "CFLAGS= -O -DPOSIX -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP \ -DRENAME -traditional -fpcc-struct-return -fstrength-reduce \ -DM_BITFIELDS -DM_COFF -DM_I386 -DM_I86 -DM_I86SM \ -DM_INTERNAT -DM_SDATA -DM_STEXT -DM_SYS3 -DM_SYS5 \ -DM_SYSIII -DM_SYSV -DM_UNIX -DM_WORDSWAP -DM_XENIX -Dunix \ -DPID_T=pid_t -DPWID_T=int $(KFLAGS) " "LNKFLAGS = -s" \ "LIBS = -lc_s -lc -lx" #SCO UNIX/386 3.2v2 (ODT 1.1) (POSIX job control) with SCO TCP/IP, shared libs #Requires SCO TCP/IP or ODT development system for telnet.h, etc. sco3r22net: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2.2 + TCP/IP...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following three continued lines into one line.' make wermit \ "CFLAGS= -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP -DTCPSOCKET \ -DRENAME -DPID_T=pid_t -DPWID_T=int -DDIRENT -DDYNAMIC \ $(KFLAGS) -O" "LNKFLAGS = -s" "LIBS = -lsocket -lc_s -lc -lx" #As above, but with curses for fullscreen file transfer display. #Requires SCO TCP/IP or ODT development system for telnet.h, etc. sco3r22netc: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2v2 + TCP/IP...' @echo 'Warning: If make blows up, edit the makefile to join' @echo 'the following three continued lines into one line.' make wermit "CFLAGS= \ -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DRDCHK -DNAP -DTCPSOCKET -DRENAME \ -DCK_CURSES -DDIRENT -DDYNAMIC \ -DPID_T=pid_t -DPWID_T=int -O $(KFLAGS)" \ "LNKFLAGS = -s" "LIBS = -lcurses -lsocket -lc_s -lc -lx" #SCO UNIX/386 3.2v4 (POSIX job control), curses, ANSI C compilation, # (EAFS) file system. Remove -lmalloc if it causes trouble. #It was put there to avoid core dumps caused by regular libc.a malloc. #CK_POLL is used instead of SELECT because SELECT requires gettimeofday(), #which is in libsocket.a, which is available only on systems with the #TCP/IP development system. Add -J to make all chars unsigned. sco32v4: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2v4...' @echo 'If you get _ftime redefinition_ complaint,' @echo 'Try adding -DODT30 to CFLAGS.' make wermit \ "CFLAGS= -DXENIX -DSVR3 -DDIRENT -DNOFILEH -DHDBUUCP -DCK_POLL -DNAP \ -DRENAME -DCK_CURSES -DM_TERMINFO -DNOANSI -DPID_T=pid_t -DPWID_T=int \ -DNOSETBUF -DDYNAMIC -DSVR3JC -DCK_RTSCTS $(KFLAGS) -O" \ "LNKFLAGS = -s" "LIBS = -lcurses -lmalloc -lc_s -lc -lx" #SCO UNIX/386 3.2v4 with gcc 1.40 or later, POSIX job control #gcc 1.40 or later. Also see comments in sco32r4 entry. sco32v4gcc: make wermit "CC = gcc" \ "CFLAGS= -O -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DCK_POLL -DNAP \ -DNOANSI -DRENAME -DDIRENT -DCK_CURSES -DM_TERMINFO -DNOSETBUF \ -traditional -fpcc-struct-return -fstrength-reduce \ -D_KR -D_NO_PROTOTYPE -D_SVID \ -DM_BITFIELDS -DM_COFF -DM_I386 -DM_I86 -DM_I86SM \ -DM_INTERNAT -DM_SDATA -DM_STEXT -DM_SYS3 -DM_SYS5 \ -DM_SYSIII -DM_SYSV -DM_UNIX -DM_WORDSWAP -DM_XENIX -Dunix \ -DPID_T=pid_t -DPWID_T=int -DSVR3JC -DCK_RTSCTS $(KFLAGS) " \ "LNKFLAGS = -s" "LIBS = -lcurses -lc_s -lc -lx" #SCO UNIX/386 3.2v4 (POSIX job control), TCP/IP, curses, ANSI C compilation, #Requires SCO TCP/IP or ODT development system for telnet.h, etc. # (EAFS) file system. With DIRENT, -lc must come before -lx. #gcc 1.40 or later. Also see comments in sco32r4 entry. sco32v4netgcc: make wermit "CC = gcc" "CC2=gcc" \ "CFLAGS= -O2 -DXENIX -DSVR3 -DNOFILEH -DHDBUUCP -DSELECT -DNAP \ -DNOANSI -DRENAME -DTCPSOCKET -DDIRENT -DCK_CURSES -DM_TERMINFO \ -DNOSETBUF -DDYNAMIC -D_KR -D_NO_PROTOTYPE -D_SVID \ -DM_BITFIELDS -DM_COFF -DM_I386 -DM_I86 -DM_I86SM \ -DM_INTERNAT -DM_SDATA -DM_STEXT -DM_SYS3 -DM_SYS5 \ -DM_SYSIII -DM_SYSV -DM_UNIX -DM_WORDSWAP -DM_XENIX -Dunix \ -DPID_T=pid_t -DPWID_T=int -DSVR3JC -DCK_RTSCTS $(KFLAGS) " \ "LNKFLAGS = -s" "LIBS = -lcurses -lsocket -lc_s -lc -lx" #SCO UNIX/386 3.2v4 (POSIX job control), TCP/IP, curses, ANSI C compilation, # (EAFS) file system. With DIRENT, -lc must come before -lx. #Reportedly it's OK to add -DCK_REDIR and -DCK_WREFRESH, and to remove -lc_s. #Requires SCO TCP/IP development system or ODT for telnet.h, etc. #See sco32v4 above for additional comments. sco32v4net: @echo 'Making C-Kermit $(CKVER) for SCO UNIX/386 3.2v4...' @echo 'If you get _ftime redefinition_ complaint,' @echo 'use make sco_odt30.' $(MAKE) wermit \ "CFLAGS= -DXENIX -DSVR3 -DDIRENT -DNOFILEH -DHDBUUCP -DRENAME \ -DDYNAMIC -DTCPSOCKET -DCK_ANSIC -DCK_CURSES -DNAP -DCK_WREFRESH \ -D_IBCS2 -DSELECT -DNOSETBUF -DPID_T=pid_t -DPWID_T=int -DSVR3JC \ -DCK_RTSCTS -O -DCK_SCOV4 $(KFLAGS)" "LNKFLAGS = $(LNKFLAGS) -s" \ "LIBS = $(LIBS) -lcurses -lsocket -lmalloc -lc_s -lc -lx" sco32v4netnd: @echo sco32v4net with no debug $(MAKE) "MAKE=$(MAKE)" sco32v4net \ "KFLAGS=$(KFLAGS) -DNODEBUG -DNOTLOG" "LIBS=$(LIBS)" sco3r2netnd: @echo sco32v4netnd built for SCO XENIX 2.3 under SCO UNIX... @echo requires copying /lib/386/Slibc.a to /lib/386/Slibc_s.a and @echo getting /lib/386/Slibsocket.a from a XENIX devkit. @echo WARNING: poll/CK_POLL supported only on XENIX 2.3.4 echo For earlier XENIX systems, replace CK_POLL with RDCHK. $(MAKE) "MAKE=$(MAKE)" sco32v4netnd \ "KFLAGS=$(KFLAGS) -x2.3 -DNORENAME" "LNKFLAGS = $(LNKFLAGS) -x2.3" \ "LIBS=-ldir $(LIBS)" sco_odt30: @echo SCO ODT 3.0 $(MAKE) "MAKE=$(MAKE)" sco32v4net "KFLAGS=$(KFLAGS) -DODT30" #SCO OpenServer 5.0 (SCO UNIX 3.2v5.0) with SCO development tools, no TCP/IP. #SCO OSR5 is much more like standard System V than previous SCO releases. #Thanks to Robert Lipe for the simplified makefile entries. sco32v5: @echo Making C-Kermit $(CKVER) for SCO OpenServer Release 5... $(MAKE) wermit CC=$(CC) CC2=$(CC2) \ "CFLAGS= -O -DBIGBUFOK -DDYNAMIC -DDIRENT -DHDBUUCP -DSVR4 -DCK_SCOV5 \ -DCK_RTSCTS -DCK_CURSES -DCK_WREFRESH -DCK_NEWTERM -DSELECT \ -DSELECT_H $(KFLAGS)" "LIBS=-lcurses $(LIBS)" "LNKFLAGS=-s $(LNKFLAGS)" #SCO OpenServer 5.0 with gcc, no networking. sco32v5gcc: @echo Using gcc... $(MAKE) "MAKE=$(MAKE)" sco32v5 CC=gcc CC2=gcc #SCO OpenServer 5.0 with networking, SCO development tools. #Networking libraries are now provided with the OS. sco32v5net: @echo TCP/IP networking added... $(MAKE) "MAKE=$(MAKE)" sco32v5 KFLAGS="-DTCPSOCKET $(KFLAGS)" \ LIBS="-lsocket" #SCO OpenServer 5.0 with networking, gcc. sco32v5netgcc: @echo TCP/IP networking added - using gcc... $(MAKE) "MAKE=$(MAKE)" sco32v5 CC=gcc CC2=gcc KFLAGS="-DTCPSOCKET" \ LIBS="-lsocket" #SCO OpenServer 5.0 with networking, gcc, elf. sco32v5netgccelf: @echo TCP/IP networking added - using gcc, dynamic elf library $(MAKE) "MAKE=$(MAKE)" sco32v5 CC=gcc CC2=gcc \ KFLAGS="-DTCPSOCKET -O3 -belf" \ LNKFLAGS="-belf" LIBS="-lsocket" #PC/IX, Interactive Corp System III for IBM PC/XT pcix: @echo 'Making C-Kermit $(CKVER) for PC/IX...' $(MAKE) wermit \ "CFLAGS= -DPCIX -DISIII $(KFLAGS) -Dsdata=sdatax -O -i" "LNKFLAGS = -i" #Integrated Solutions Inc V8S VME 68020 isi: @echo Making C-Kermit $(CKVER) for 4.2BSD on ISI... $(MAKE) wermit "CC = cc" \ "CFLAGS= -DBSD4 -DTCPSOCKET -DINADDRX -DDCLPOPEN -DDEBUG -DNOSETREU \ -DCK_CURSES $(KFLAGS)" "LIBS = -lcurses -ltermcap" #Interactive Corp System III port in general -- #is3: (very old, probably not sufficient for 5A) # @echo 'Making C-Kermit $(CKVER) for Interactive System III...' # make wermit "CFLAGS = -DISIII -Ddata=datax -O -i" "LNKFLAGS = -i" #The following should work, use it if you don't have gcc. #Use is3gcc if you have gcc. is3: @echo 'Making C-Kermit $(CKVER) for Interactive System III...' $(MAKE) wermit \ "CFLAGS= -DISIII $(KFLAGS) -Ddata=datax -DNAP -DHDBUUCP -DLOCK_DIR=\"/usr/spool/uucp\" -DSIGTYP=void -O -i' "LNKFLAGS = -i" #Interactive UNIX System V R3, no network support. Uses and Honey #DanBer UUCP. If this entry does not compile correctly, try any or all of the #following. These suggestions also apply more or less to the other is5r3xxx #entries that follow this one. # . Remove the UID_T and GID_T definitions, or change them as required. # . Change -DDIRENT to -DSDIRENT. # . Add -DSIGTYP=void. # . Remove -g from LNKFLAGS. # . Add -DNOANSI to remove compiler complaints about ANSI C constructions # . Add other -DNOxxx's to save space (e.g. -DNOCSETS) # See the next few makefile entries for related examples. is5r3: @echo 'Making C-Kermit $(CKVER) for Interactive 386/ix or later...' @echo 'If this does not work please read the makefile entry.' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -g -DNOCSETS \ -DUID_T=ushort -DGID_T=ushort -DDYNAMIC -DI386IX $(KFLAGS)" \ "LNKFLAGS = -g" #Interactive Corp System System V R3 with gcc is3gcc: @echo 'Making C-Kermit $(CKVER) for Interactive System V R3 / gcc...' $(MAKE) wermit CC=gcc CC2=gcc \ 'CFLAGS = -D_SYSV3 -DISIII -Ddata=datax -DNAP -DHDBUUCP \ -DLOCK_DIR=\"/usr/spool/uucp\" -DSIGTYP=void -O' "LNKFLAGS =" #Interactive UNIX System V R3, POSIX variant. Untested. #Uses dirent.h and Honey DanBer uucp. Read comments in is5r3 entry. is5r3p: @echo 'Making C-Kermit $(CKVER) for Interactive 386/ix or later...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DHDBUUCP -g -DNOCSETS \ -DDYNAMIC -DI386IX -DPOSIX $(KFLAGS)" "LNKFLAGS=" "LIBS=-lcposix" #Interactive UNIX SVR3 2.2.1, job control, curses, no net, gcc. is5r3gcc: $(MAKE) wermit CC=gcc CC2=gcc \ "CFLAGS=-g -posix -DSVR3 -DDIRENT \ -DHDBUUCP -O -DNOCSETS -DDYNAMIC -DI386IX -DSVR3JC -DCK_CURSES \ $(KFLAGS)" LNKFLAGS="-posix" LIBS="-lcurses -lc_s" #Interactive UNIX System V R3 with TCP/IP network support. #Needs -linet for net functions. signal() is void rather than int. #Uses dirent.h and Honey DanBer uucp. Read comments in is5r3 entry. #Also see is5r3net2 if you have trouble with this entry. is5r3net: @echo 'Making C-Kermit $(CKVER) for Interactive 386/ix...' @echo 'If this does not work please read the makefile entry.' $(MAKE) wermit CC="$(CC)" CC2="$(CC2)" \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DTCPSOCKET \ -DI386IX $(KFLAGS) -O" "LIBS = -linet" is5r3netgcc: $(MAKE) is5r3net CC=gcc CC2=gcc #Interactive UNIX System V R3, no job control, signal() void rather than int. #Uses dirent.h and Honey DanBer uucp. Needs -linet for net functions. #Read comments in is5r3 entry. Use this entry if is5r3net fails. #Saves some space by stripping (-s) and using shared library (-lc_s). is5r3net2: @echo 'Making C-Kermit $(CKVER) for Interactive 386/ix...' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DTCPSOCKET -DNOJC \ -DSIGTYP=void -DNOANSI -DI386IX $(KFLAGS) -O" \ "LNKFLAGS= -s" "LIBS = -linet -lc_s" #Interactive UNIX System V R3 (version 2.2 or later) with job control & curses. #Uses dirent.h and Honey DanBer UUCP. is5r3jc: @echo 'Making C-Kermit $(CKVER) for Interactive Unix 2.2 or later...' $(MAKE) wermit CC="$(CC)" CC2="$(CC2)" \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -O -DNOCSETS \ -DUID_T=ushort -DGID_T=ushort -DDYNAMIC -DI386IX -DSVR3JC -DCK_CURSES \ -DPOSIX_JC -DCK_REDIR -DNOSETBUF \ -DCK_POLL \ $(KFLAGS)" "LIBS=-lcurses -lc_s" is5r3jcgcc: $(MAKE) is5r3jc CC="gcc -DCK_ANSILIBS -DDCGPWNAM -O4" CC2=gcc \ KFLAGS="$(KFLAGS)" LNKFLAGS="$(LNKFLAGS)" #Sunsoft/Interactive UNIX System V R3 (version 2.2 or later) #with job control, curses, and TCP/IP networking. #Uses dirent.h and Honey DanBer UUCP. is5r3netjc: @echo 'Making C-Kermit $(CKVER) for Interactive Unix 2.2 or later...' $(MAKE) wermit CC="$(CC)" CC2="$(CC2)" \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -O -DNOCSETS \ -DUID_T=ushort -DGID_T=ushort -DDYNAMIC -DI386IX -DSVR3JC -DCK_CURSES \ -DPOSIX_JC -DCK_REDIR -DNOSETBUF \ -DTCPSOCKET -DSELECT -DHADDRLIST \ $(KFLAGS)" "LIBS=-linet -lcurses -lc_s" is5r3netjcgcc: $(MAKE) is5r3netjc CC="gcc -DCK_ANSILIBS -DDCGPWNAM -O4" CC2=gcc \ KFLAGS="$(KFLAGS)" LNKFLAGS="$(LNKFLAGS)" #Masscomp System III rtu: @echo 'Making C-Kermit $(CKVER) for Masscomp RTU System III...' $(MAKE) wermit \ "CFLAGS= -UFIONREAD -DATTSV $(KFLAGS) -O" "LNKFLAGS =" "LIBS= -ljobs" #Masscomp/Concurrent RTU 4.0 or later, Berkeley environment. #Includes = /usr/include/ndir.h #Note "LIBS = -lndir" might not be necessary because of "ucb make". rtubsd: @echo 'Making C-Kermit $(CKVER) for Masscomp RTU 4.1A...' ucb make wermit \ "CFLAGS= -DBSD4 -DRTU -DNDIR -DHDBUUCP -DTCPSOCKET $(KFLAGS)" \ "LIBS = -lndir" #Masscomp/Concurrent RTU 4.0 or later, same as above, #Includes "usr/lib/ndir.h" #Note "LIBS = -lndir" might not be necessary because of "ucb make". rtubsd2: @echo 'Making C-Kermit $(CKVER) for Masscomp RTU 4.1A...' ucb make wermit \ "CFLAGS= -DBSD4 -DRTU -DXNDIR -DHDBUUCP $(KFLAGS)" \ "LIBS = -lndir" #Masscomp/Concurrent RTU 4.0 or later, same as above, #Includes #Note "LIBS = -lndir" might not be necessary because of "ucb make". rtubsd3: @echo 'Making C-Kermit $(CKVER) for Masscomp RTU 4.x BSD...' ucb make wermit "CFLAGS= -DBSD4 -DRTU -DHDBUUCP $(KFLAGS)" \ "LIBS = -lndir" #Masscomp/Concurrent RTU 4.0 or later, System V R2, using . #In case of problems, add back the -DRTU switch. #In case -DTCPSOCKET gives trouble, remove it. rtus5: @echo 'Making C-Kermit $(CKVER) for Masscomp RTU 4.x...' $(MAKE) wermit \ "CFLAGS= -DATTSV -DHDBUUCP -DDIRENT -DTCPSOCKET -DDYNAMIC \ -DNOSETBUF $(KFLAGS)" #Masscomp/Concurrent RTU 4.x, System V R3, using . #Use this one if rtus5 gives warnings about pointer type mismatches. #In case of problems, add back the -DRTU switch. rtus5r3: @echo 'Making C-Kermit $(CKVER) for Masscomp RTU Sys V R3...' $(MAKE) wermit "CFLAGS= -DSVR3 -DHDBUUCP -DDIRENT $(KFLAGS)" #DEC Pro-3xx with Pro/Venix V1.0 or V1.1 # Requires code-mapping on non-I&D-space 11/23 processor, plus some # fiddling to get interrupt targets into resident code section. # This almost certainly doesn't work any more. provx1: @echo 'Making C-Kermit $(CKVER) for DEC Pro-3xx, Pro/Venix 1.x...' $(MAKE) wart "CFLAGS= -DPROVX1 $(KFLAGS)" "LNKFLAGS= " $(MAKE) wermit "CFLAGS = -DPROVX1 -DNOFILEH -md780" \ "LNKFLAGS= -u _sleep -lc -md780" #Nixdorf Targon/31. #AT&T UNIX System V R3, signal() is void rather than int. #Uses dirent.h without Honey DanBer uucp. t31tos40x: @echo 'Making C-Kermit $(CKVER) for Targon/31 with TOS 4.0.xx...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DDYNAMIC $(KFLAGS) -O" \ "LNKFLAGS=" #NCR Tower 1632, OS 1.02 tower1: @echo 'Making C-Kermit $(CKVER) for NCR Tower 1632, OS 1.02...' $(MAKE) wermit "CFLAGS= -DTOWER1 $(KFLAGS)" #NCR Tower 32, OS Release 1.xx.xx tower32-1: @echo 'Making C-Kermit $(CKVER) for NCR Tower 32 Rel 1 System V R2...' @echo 'Add KFLAGS=-DISDIRBUG if you get errors about S_ISREG/S_ISDIR.' $(MAKE) wermit \ "CFLAGS = -DATTSV -DDYNAMIC $(KFLAGS) -O" "LNKFLAGS = -n" #NCR Tower 32, OS Release 2.xx.xx tower32-2: @echo 'Making C-Kermit $(CKVER) for NCR Tower 32 Rel 2 System V R2...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DHDBUUCP -DDYNAMIC $(KFLAGS) -O2" \ "LNKFLAGS = -n" #NCR Tower 32, OS Releases based on System V R3 #Don't add -DNAP (doesn't work right) or -DRDCHK (not available in libc). tower32: @echo 'Making C-Kermit $(CKVER) for NCR Tower 32 System V R3...' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DNOSYSIOCTLH $(KFLAGS) \ -DUID_T=ushort -DGID_T=ushort -O1" #NCR Tower 32, OS Releases based on System V R3 tower32g: @echo 'Making C-Kermit $(CKVER) for NCR Tower 32 System V R3, gcc...' $(MAKE) wermit "CC = gcc" \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DNOSYSIOCTLH $(KFLAGS) \ DUID_T=ushort -DGID_T=ushort -O -fstrength-reduce -fomit-frame-pointer" #Fortune 32:16, For:Pro 1.8 (mostly like 4.1bsd) ft18: @echo 'Making C-Kermit $(CKVER) for Fortune 32:16 For:Pro 1.8...' $(MAKE) wermit \ "CFLAGS= -DNODEBUG -DBSD4 -DFT18 -DNOFILEH $(KFLAGS) \ -DPID_T=short" #Fortune 32:16, For:Pro 2.1 (mostly like 4.1bsd). #The modules that break the optimizer are compiled separately. ft21: @echo 'Making C-Kermit $(CKVER) for Fortune 32:16 For:Pro 2.1...' $(MAKE) ckuusx.$(EXT) "CFLAGS= -DNODEBUG -DBSD4 -DFT21 -DNOFILEH \ -SYM 800 -DDYNAMIC -DNOSETBUF -DCK_CURSES $(KFLAGS) -DPID_T=short" \ "LNKFLAGS= -n -s" "LIBS= -lcurses -ltermcap -lv -lnet" $(MAKE) ckuxla.$(EXT) "CFLAGS= -DNODEBUG -DBSD4 -DFT21 -DNOFILEH \ -SYM 800 -DDYNAMIC -DNOSETBUF -DCK_CURSES $(KFLAGS) -DPID_T=short" \ "LNKFLAGS= -n -s" "LIBS= -lcurses -ltermcap -lv -lnet" $(MAKE) ckudia.$(EXT) "CFLAGS= -DNODEBUG -DBSD4 -DFT21 -DNOFILEH \ -SYM 800 -DDYNAMIC -DNOSETBUF -DCK_CURSES $(KFLAGS) -DPID_T=short" \ "LNKFLAGS= -n -s" "LIBS= -lcurses -ltermcap -lv -lnet" $(MAKE) wermit \ "CFLAGS= -O -DNODEBUG -DBSD4 -DFT21 -DNOFILEH -SYM 800 \ -DDYNAMIC -DNOSETBUF -DCK_CURSES $(KFLAGS) -DPID_T=short" \ "LNKFLAGS= -n -s" "LIBS= -lcurses -ltermcap -lv -lnet" #Valid Scaldstar #Berkeleyish, but need to change some variable names. valid: @echo 'Making C-Kermit $(CKVER) for Valid Scaldstar...' $(MAKE) wermit \ "CFLAGS= -DBSD4 -DNODEBUG -DNOTLOG -Dcc=ccx -DFREAD=1 $(KFLAGS)" #IBM IX/370 on IBM 370 Series mainframes #Mostly like sys3, but should buffer packets. ix370: @echo 'Making C-Kermit $(CKVER) for IBM IX/370...' $(MAKE) wermit "CFLAGS = -DIX370 -DATTSV $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Amdahl UTS 2.4 on IBM 370 series compatible mainframes. #Mostly like V7, but can't do initrawq() buffer peeking. uts24: @echo 'Making C-Kermit $(CKVER) for Amdahl UTS 2.4...' $(MAKE) wermit "CFLAGS=-DV7 -DPROCNAME=\\\"$(PROC)\\\" \ -DUTS24 -DBOOTNAME=\\\"$(BOOTFILE)\\\" -DNPROCNAME=\\\"$(NPROC)\\\" \ -DNPTYPE=$(NPTYPE) $(DIRECT) $(KFLAGS)" #Amdahl UTSV UNIX System V = System V R2 or earlier. utsv: @echo 'Making C-Kermit $(CKVER) for Amdahl UTSV...' $(MAKE) wermit \ "CFLAGS = -DUTSV $(KFLAGS) -i -O" "LNKFLAGS = -i" #Amdahl UTSV UNIX System V = System V R2 or earlier, with TCP sockets library. utsvtcp: @echo 'Making C-Kermit $(CKVER) for Amdahl UTSV w/tcp...' $(MAKE) wermit "CFLAGS = \ -DTCPSOCKET -DUTSV $(KFLAGS) -i -O" "LNKFLAGS = -i" \ "LIBS = -lsocket" #BBN C/70 with IOS 2.0 #Mostly Berkeley-like, but with some ATTisms c70: @echo 'Making C-Kermit $(CKVER) for BBN C/70 IOS 2.0...' $(MAKE) wermit "CFLAGS= -DBSD4 -DC70 $(KFLAGS)" #Zilog ZEUS 3.21 zilog: @echo 'Making C-Kermit $(CKVER) for Zilog Zeus 3.21...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DZILOG -DNODEBUG $(KFLAGS) -i -O" \ "LNKFLAGS = -i -lpw" #Whitechapel MG-1 Genix 1.3 white: @echo 'Making C-Kermit $(CKVER) for Whitechapel MG-1 Genix 1.3...' @touch ckcpro.c $(MAKE) wermit "CFLAGS= -DBSD4 -Dzkself()=0 $(KFLAGS)" #Pixel 1000 pixel: @echo 'Making C-Kermit $(CKVER) for Pixel 1000...' $(MAKE) wermit "CFLAGS= -DBSD4 -Dzkself()=0 $(KFLAGS)" ptx: $(MAKE) "MAKE=$(MAKE)" dynixptx12 #CDC VX/VE 5.2.1 vxve: @echo 'Making C-Kermit $(CKVER) for CDC VX/VE 5.2.1...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DVXVE -DNODEBUG -DNOTLOG $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Tandy 16/6000 with Xenix 3.0 #Add more -DNOxxx options to remove features if program won't load. #Successful operation is a function of program size, physical memory, #available swap space, etc. The following stripped-down configuration #seems to work on most Tandy 6000s. NOTE: "-+" means allow long variable #names, needed for C-Kermit 6.0 because some identifiers are not unique #within the first six characters. trs16: @echo 'Making C-Kermit $(CKVER) for Tandy 16/6000, Xenix 3.0...' $(MAKE) wermit \ "CFLAGS = -+ -DATTSV -DTRS16 -DNOMKDIR -DDCLPOPEN -DCK_CURSES \ -DDYNAMIC -DNODEBUG -DNOTLOG -DNOHELP -DNOSCRIPT -DNOCSETS \ $(KFLAGS) -O" "LIBS= -lcurses -ltermcap" "LNKFLAGS = -+ -n -s" #DIAB DS90 or LUXOR ABC-9000 with pre-5.2 DNIX. Sys V with nap() and rdchk(). # nd = no opendir(), readdir(), closedir(), etc. # Some of the modules fail to compile with -O. dnixnd: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with very old DNIX 5.2.' $(MAKE) wermit \ "CFLAGS = -DATTSV -DNAP -DRDCHK -DDYNAMIC -DDCLPOPEN \ -U__STDC__ $(KFLAGS)" #DIAB DS90 with DNIX 5.2. Sys V with nap() and rdchk(). # This one has opendir(), readdir(), closedir(), etc. # Some of the modules fail to compile with -O. dnix: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with old DNIX 5.2...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DNAP -DRDCHK -DDIRENT -DDYNAMIC \ -U__STDC__ $(KFLAGS)" #DIAB DS90 with DNIX 5.2. Sys V with nap() and rdchk(). # As above, but with curses and TCP/IP. # You might get complaints about redefinition of O_RDONLY, etc, because # of bugs in the DNIX header files, which can be fixed by adding #ifndef... # around the offending definitions in the header files. dnixnetc: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with old DNIX 5.2...' $(MAKE) wermit \ "CFLAGS = -DATTSV -DNAP -DRDCHK -DDIRENT -DDYNAMIC \ -DTCPSOCKET -DCK_CURSES -I/usr/include/bsd -U__STDC__ $(KFLAGS)" \ "LIBS = -ln -lcurses" #DIAB DS90 with DNIX 5.3 or later, with HDB UUCP, nap() and rdchk(). dnix5r3: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with DNIX 5.3...' @echo 'with Honey DanBer UUCP' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DHDBUUCP -DNAP -DRDCHK -DDIRENT \ -DDYNAMIC -DCK_CURSES -DRENAME $(KFLAGS) -O" "LIBS= -lcurses" #DIAB DS90 with DNIX 5.3 or later, with HDB UUCP, nap() and rdchk() + TCP/IP dnix5r3net: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with DNIX 5.3...' @echo 'with Honey DanBer UUCP and TCP/IP' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DHDBUUCP -DNAP -DRDCHK -DDIRENT \ -DTCPSOCKET -DDYNAMIC -DCK_CURSES -DRENAME $(KFLAGS) -O \ -I/usr/include/bsd" "LIBS = -ln -lcurses" #DIAB DS90 with DNIX 5.3 2.2 or later, with HDB UUCP, nap() and rdchk(), #ANSI C compilation and libraries. #Note that for DNIX 5.3 2.2 you have to correct a bug in /usr/include/stdlib.h: #change "extern void free(char *str);" #to "extern void free(void *str);" #NOTE: This bug is reportedly fixed in DNIX 5.3 2.2.1. #Should you get fatal errors caused by harmless pointer-type mismatches, #like between signed and unsigned char, just remove -X7. dnix5r3ansi: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with DNIX 5.3...' @echo 'with ANSI C Honey DanBer UUCP' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIAB -DHDBUUCP -DNAP -DRDCHK -DDIRENT -DDYNAMIC \ -DCK_ANSILIBS -DCK_CURSES -DRENAME -O -X7 -X9 $(KFLAGS)" \ "LIBS= -lcurses" #DIAB DS90 with DNIX 5.3 2.2 or later, with HDB UUCP, nap() and rdchk(), # + TCP/IP, ANSI C compilation and libraries. #Should you get fatal errors caused by harmless pointer-type mismatches, #like between signed and unsigned char, just remove -X7. dnix5r3ansinet: @echo 'Making C-Kermit $(CKVER) for DIAB DS90 with DNIX 5.3...' @echo 'with ANSI C Honey DanBer UUCP' $(MAKE) wermit \ "CFLAGS = -DSVR3 -DDIAB -DHDBUUCP -DNAP -DRDCHK -DDIRENT -DDYNAMIC \ -DTCPSOCKET -DCK_ANSILIBS -DCK_CURSES -DRENAME -O -X7 -X9 $(KFLAGS) \ -I/usr/include/bsd" "LIBS= -ln -lcurses" # QNX 4.21 and above, 32-bit version, Watcom C32 10.6, register calling # conventions, fully configured, except no job control because QNX 4.x # does not support it. New NCURSES library used instead of CURSES. # # -Oatx optimizes to favor speed over size: loop optimization, inline fn's. # -Os favors size over speed. The size difference is about 30-40K. # -NOUUCP is included because QNX is shipped without UUCP and no native # QNX software uses UUCP lockfiles. Remove -DNOUUCP if you want to use # UUCP lockfiles for exclusive access to dialout devices. qnx32: @echo 'Making C-Kermit $(CKVER) for QNX 4.2x, 32-bit...' $(MAKE) wermit \ "LNKFLAGS = -3r" \ "CFLAGS = -3r -ms -DQNX -DDYNAMIC -DKANJI -DTCPSOCKET -DCK_CURSES \ -DCK_WREFRESH -DCK_REDIR -DSELECT -DSELECT_H -DCK_RTSCTS -DNOJC \ -DNOUUCP -DNOSETBUF -DCK_ANSIC -DPID_T=pid_t -Oatx -zc $(KFLAGS)" \ "LIBS= -lsocket -lncurses -ltermcap" @wermit -h >use.qnx @usemsg wermit use.qnx @rm use.qnx # Synonym for qnx32. qnx: $(MAKE) qnx32 "KFLAGS=$(KFLAGS)" # QNX 4.21 and above, 16-bit version, Watcom C 8.5 - Watcom 9.52 # on i286 PCs and above. # # IMPORTANT: Do not use Watcom C 10.6!!! # If you have it installed, add "-v9.52 to CFLAGS" # # NOTE: QNX 4.23 onward does not work on 286's anyway. # Stacksize 26000, objects larger than 100 bytes in their own segments, # string constants to the codesegment, etc. Fully configured except job ctrl. # This entry works for building a 16-bit executable on a 32-bit system, but # has not been tested on a 16-bit system. Uses large memory model, links # explicitly with large-model sockets library. Correct-model curses library # is chosen automatically. See comment in qnx32 entry about -DNOUUCP. # # WARNING: # # Watcom C prior to 10.6 never had released curses library. To link against it, # you must obtain ported free curses source from ftp://ftp.qnx.com/usr/free, # then compile and build library (cursesl.lib) and place it in /usr/lib. You # must also copy curses.h to /usr/include. Be aware that if you have Watcom # 10.6 installed, you should already have curses.h, which is for new ncurses # library. You must back it up and use free curses.h instead, since ncurses is # only for 32-bit applications and some definitions in these files are # different (e.g., clearok()). # qnx16: @echo 'Making C-Kermit $(CKVER) for QNX 4.21, 16-bit...' $(MAKE) wermit \ "LNKFLAGS = -2 -ml -N 26000" \ "CFLAGS = -2 -Oatx -zc -zt100 -ml -DNOSETBUF -DNOUUCP \ -DQNX -DDYNAMIC -DCK_REDIR -DSELECT -DSELECT_H -DNOJC -DTCPSOCKET \ -DCK_RTSCTS -DCK_CURSES -DCK_WREFRESH -DCK_ANSIC -DKANJI \ -DPID_T=pid_t $(KFLAGS)" \ "LIBS=-lsocketl -lcurses -ltermcap -ltermlib" @wermit -h >use.qnx @usemsg wermit use.qnx @rm use.qnx # QNX 4.1, 16-bit version, with Watcom C 8.5 on i286 PCs and above. # stacksize 26000, objects larger than 100 bytes in their own segments, # string constants to the codesegment, etc. Add -DNOUUCP if desired. qnx16_41: @echo 'Making C-Kermit $(CKVER) for QNX 4.1, 16-bit...' $(MAKE) wermit \ "LNKFLAGS = -mh -N 26000" "CFLAGS = -Wc,-fpc -Wc,-j \ -Wc,-Ols -Wc,-zdf -Wc,-zc -Wc,-zt100 -mh -DPOSIX -DQNX -DDIRENT \ -DNOCYRIL -DNODEBUG -DNOMSEND -DMINIDIAL -DNOXMIT -DNOSCRIPT -DNOSPL \ -DNOSETKEY -DDYNAMIC -DPID_T=pid_t $(KFLAGS)" @wermit -h >use.qnx @usemsg wermit use.qnx @rm use.qnx #Ridge 32 with ROS 3.2 ridge32: @echo 'Making C-Kermit $(CKVER) Ridge 32 ROS 3.2' $(MAKE) wermit \ "CFLAGS = -DATTSV -DNOFILEH -DNODEBUG -DNOTLOG $(KFLAGS) -i -O" \ "LNKFLAGS = -i" #Altos 486, 586, or 986 with Xenix 3.0 altos: @echo 'Making C-Kermit $(CKVER) for Altos x86 with Xenix 3.0...' $(MAKE) wermit \ "CFLAGS= -DATTSV -DA986 -DNODEBUG -DNOTLOG $(KFLAGS) -i -O" \ "LNKFLAGS= -i" #Altos 986 with Xenix 3.0, as above, but command-line only, minimal size. #For systems with small memories. It might also be necessary to chop certain #modules up into smaller pieces, e.g. ckuus3-6, because of symbol table #overflow. If this makefile is too big or complex for the Altos, compile #and link by hand or write shell scripts. altosc: @echo 'Making C-Kermit $(CKVER) for Altos x86 Xenix 3.0, remote...' $(MAKE) wermit \ "CFLAGS= -DATTSV -DA986 -DNODEBUG -DNOTLOG -DNOSCRIPT -DNODIAL \ -DNOCSETS -DNOANSI -DNOMSEND -DNOSPL -DNOICP $(KFLAGS) -Mm -O" \ "LNKFLAGS= -Mm -s" #Altos 986 with Xenix 3.0, as above, but interactive only, minimal size. altosi: @echo 'Making C-Kermit $(CKVER) for Altos x86 Xenix 3.0, local...' $(MAKE) wermit \ "CFLAGS= -DATTSV -DA986 -DNODEBUG -DNOTLOG -DNOSCRIPT -DNODIAL \ -DNOCSETS -DNOANSI -DNOMSEND -DNOSPL -DNOCMDL -DNOFRILLS -DNOHELP \ -DNOSETKEY $(KFLAGS) -Mm -O" "LNKFLAGS= -Mm -s" # Altos ACS68000 68000 System, UNIX System 3 Release 2, 512k memory. # also needs getcwd() external function; see ckuins.doc file. # also, sys/types.h needed modifying: # #ifdef __SYS_TYPES_H__, #define ..., #endif # also, ckuus2.c MUST be compiled NOOPT else symbol table is destroyed! # Submission by Robert Weiner/Programming Plus, rweiner@progplus.com. # altos3: @echo 'Making C-Kermit $(CKVER) for Altos ACS68k UNIX System III' $(MAKE) ckuus2.$(EXT) "CFLAGS = -DATTSV -DNOCSETS -DNOSETKEY -DNOJC \ -DNODIAL -DDCLPOPEN -DNOSETBUF -DNOSCRIPT -DNOHELP $(KFLAGS) -i" $(MAKE) wermit \ "CFLAGS = -DATTSV -DNOCSETS -DNOSETKEY -DNOJC \ -DNODIAL -DDCLPOPEN -DNOSETBUF -DNOSCRIPT -DNOHELP $(KFLAGS) -i -O" \ "LNKFLAGS = -i" "LIBS = getcwd.$(EXT)" #MINIX - Original PC version with 64K+64K limit. # Reportedly, the linker (asld) can run out of space while linking. The only # way around this is to make a copy of libc.a from which all modules that are # not used by Kermit are removed. If you have trouble compiling or running # wart, "touch wart". If that doesn't help, "touch ckcpro.c". # The version configured below has no interactive command parser. # If you can build this version successfully, maybe there will be room for # a minimal interactive command parser too; try replacing -DNOICP with # -DNOSPL, plus every other -DNOxxx flag there is, except for -DNOICP # (see ckccfg.doc). minix: @echo 'Making C-Kermit $(CKVER) for MINIX, no command parser... @echo 'TOTALLY UNTESTED!' $(MAKE) wermit EXT=s \ "CFLAGS= -DV7 -DMINIX -i -D_MINIX -D_POSIX_SOURCE -DDYNAMIC \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t -DSIG_V \ -DNOXMIT -DNOMSEND -DNOFRILLS -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG \ -DNOSCRIPT -DNOCSETS -DNOICP -DNOSETKEY $(KFLAGS)" \ "LNKFLAGS= -i -T" #MINIX - PC version with 64K+64K limit, new (as yet unreleased) ACK 2.0 beta C #compiler, which outputs .o object files, rather than .s. But 'make' still #expects .s files, so must be patched to use .o. Tested on Minix 1.5.10. minixnew: @echo 'Making C-Kermit $(CKVER) for MINIX (new ACK 2.0 compiler),' @echo 'no command parser... TOTALLY UNTESTED!' $(MAKE) wermit \ "CFLAGS= -DV7 -DMINIX -i -D_MINIX -D_POSIX_SOURCE -DDYNAMIC \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t -DSIG_V -DNODIAL \ -DNOHELP -DNODEBUG -DNOTLOG -DNOSCRIPT -DNOCSETS -DNOICP $(KFLAGS)" \ "LNKFLAGS= -i -T" #MINIX/386 (PC Minix modified by Bruce Evans in Australia for 386 addressing) minix386: @echo 'Making C-Kermit $(CKVER) for MINIX/386...' @echo 'TOTALLY UNTESTED!' $(MAKE) wermit EXT=s \ "CFLAGS= -DV7 -DMINIX -D_POSIX_SOURCE -DDYNAMIC $(KFLAGS)" #MINIX/386 (PC Minix modifed by Bruce Evans in Australia to use 386 addressing) minix386gcc: @echo 'Making C-Kermit $(CKVER) for MINIX/386 with gcc...' @echo 'TOTALLY UNTESTED!' $(MAKE) wermit "CC=gcc -g -O" "CC2=gcc -g" \ "CFLAGS= -DV7 -DMINIX -D_POSIX_SOURCE -DDYNAMIC $(KFLAGS)" #MINIX - 68k version with ACK compiler. # If you have trouble compiling or running wart, "touch wart". # If it still doesn't work, "touch ckcpro.c". # The version configured below has many features removed, including # the TRANSMIT, MSEND, HELP, and SCRIPT commands, international # character set support, and the entire script programming language. # But it does have an interactive command parser. # Make sure make(1) has (at least) 100000 chmemory! # If you are using the Amsterdam C compiler, you might have to add "-D__ACK__". minix68k: @echo 'Making C-Kermit $(CKVER) for MINIX 68k with ACK... $(MAKE) wermit \ "CFLAGS= -DV7 -DMINIX -D_MINIX -D_POSIX_SOURCE -DDYNAMIC \ -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG \ -DNOSCRIPT -DNOCSETS -DNOSPL $(KFLAGS) \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t -DSIG_V" #MINIX - 68k version with c68 compiler. # If you have trouble compiling or running wart, "touch wart" or # "touch ckcpro.c". Compiling ckudia.c (no -DNODIAL!) might fail. :-( # Give c68 250000 bytes of stack+heap; make sure make(1) has at least # 100000 chmemory. On a 1Mb Atari ST this means that the recursive # call of make fails due to memory shortage. Try "make -n minixc68 >makeit", # followed by ". makeit". Otherwise, as above. minixc68: @echo 'Making C-Kermit $(CKVER) for MINIX 68k with c68... $(MAKE) wermit "CC= cc -c68" \ "CFLAGS= -DV7 -DMINIX -D_MINIX -D_POSIX_SOURCE -DDYNAMIC \ -DNODIAL -DNOHELP -DNODEBUG -DNOTLOG \ -DNOSCRIPT -DNOCSETS -DNOSPL $(KFLAGS) \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t -DSIG_V" #MINIX - 68k version with c68 compiler. #A variation on the above that was recently (Sep 95) reported to work. minixc68a: @echo 'Making C-Kermit $(CKVER) for MINIX 68k with c68... $(MAKE) wermit "CC= cc -c68" \ "CFLAGS= -DV7 -DMINIX -D_MINIX -D_POSIX_SOURCE -DDYNAMIC \ -DCK_ANSIC -DNODEBUG -DNOTLOG -DMINIDIAL -DEXTEN -DMYCURSES \ -DNOSCRIPT -DNOCSETS -DNOSPL -DNOJC -DDIRENT -DNOSETBUF \ -DNOSETKEY -DNOESCSEQ $(KFLAGS) \ -DPID_T=pid_t -DUID_T=uid_t -DGID_T=gid_t -DSIG_V" #MIPS Computer Systems with UMIPS RISC/OS 4.52 = AT&T UNIX System V R3.0. #Remove -DNOJC if job control can be safely used. mips: @echo 'Making C-Kermit $(CKVER) for MIPS RISC/OS...' $(MAKE) wermit \ "CFLAGS = -DMIPS -DDIRENT -DDYNAMIC -DCK_POLL -DNOJC -DPID_T=int \ -DGID_T=gid_t -DUID_T=uid_t -i -O1500 $(KFLAGS)" #As above, but with TCP/IP and fullscreen support. mipstcpc: @echo 'Making C-Kermit $(CKVER) for MIPS RISC/OS...' $(MAKE) wermit \ "CFLAGS = -DMIPS -DDIRENT -DDYNAMIC -DCK_POLL -DNOJC \ -DTCPSOCKET -DCK_CURSES -I/usr/include/bsd \ -DPID_T=int -DGID_T=gid_t -DUID_T=uid_t -i -O1500 $(KFLAGS)" \ "LIBS = -lcurses -lbsd" #Motorola Delta System V/68 R3, signal() is void rather than int. #Uses dirent.h and Honey DanBer uucp. Supports TCP/IP. #After building, use "mcs -d" to reduce size of the executable program. sv68r3: @echo 'Making C-Kermit $(CKVER) for Motorola UNIX System V/68 R3...' $(MAKE) wermit "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTCPSOCKET $(KFLAGS) \ -O" "LNKFLAGS =" #Motorola Delta System V/68 R3V5, signal() is void rather than int. #Uses dirent.h and Honey DanBer UUCP. Supports TCP/IP. #After building, use "mcs -d" to reduce size of the executable program. sv68r3v5: @echo 'Making C-Kermit $(CKVER) for Motorola UNIX System V/68 R3V5' $(MAKE) wermit "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTCPSOCKET -DINADDRX $(KFLAGS) -O" "LNKFLAGS =" "LIBS = -linet" #Motorola MVME147 System V/68 R3 V5.1. Requires gcc 2.1 to compile. #After building, use "mcs -d" to reduce size of the executable program. sv68r3v51: @echo 'Making C-Kermit $(CKVER) for Motorola UNIX System V/68 R3V5.1' $(MAKE) wermit "CC=gcc-delta" "CC2=gcc-delta" \ "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC -DNODEBUG -DNOSETBUF \ $(KFLAGS) -O2 -v -ftraditional" "LNKFLAGS = -s -v" "LIBS = -lm881" #Motorola MVME147 System V/68 R3V6. derived from Motorola Delta System R3V5. #Checked on larger Motorola System V/68 R3V6 ( with NSE Network Services Ext.) #After building, use "strip" to reduce size of the executable program. #Try removing the LIBS clause if it causes trouble (libnsl might not actually #be necessary, and reportedly it is missing on some systems). sv68r3v6: @echo 'Making C-Kermit $(CKVER) for Motorola UNIX System V/68 R3V6' @echo 'Remove the LIBS clause if it causes trouble.' $(MAKE) wermit "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTCPSOCKET $(KFLAGS) -O" "LNKFLAGS =" "LIBS = -lnsl" #Motorola Delta System V/88 R32, signal() is void rather than int. #Uses dirent.h and Honey DanBer uucp. Needs for setting #file dates. Supports TCP/IP. #After building, use "mcs -d" to reduce size of the executable program. sv88r32: @echo 'Making C-Kermit $(CKVER) for Motorola UNIX System V/88 R32...' $(MAKE) wermit "CFLAGS = -DSVR3 -DDIRENT -DHDBUUCP -DDYNAMIC \ -DTCPSOCKET -DSYSUTIMEH -DCK_CURSES $(KFLAGS) \ -O" "LIBS= -lcurses" "LNKFLAGS = -s" #Motorola Delta System V/88 R40. Has , regular Berkeley #sockets library, i.e. in.h and inet.h are not misplaced in sys (rather than #netinet and arpa, respectively). Uses ANSI C constructs, advisory file #locking on devices, etc. curses support added. Reportedly, the #/usr/include/sys/vnode.h file has a bug which must be fixed before this #makefile entry can work correctly. The "if DEBUG" directive at about line #320 must be changed to "ifdef DEBUG" (Reportedly, this was fixed in #in System V/88 R4.3). #After building, use "mcs -d" to reduce size of the executable program. sv88r40: @echo 'Making C-Kermit $(CKVER) for Motorola UNIX System V/88 R40...' $(MAKE) wermit "CFLAGS = -O -DSVR4 -DMOTSV88R4 -DDIRENT -DHDBUUCP \ -DDYNAMIC -DSTERMIOX -DTCPSOCKET -DCK_CURSES $(KFLAGS)" \ "LIBS= -lsocket -lnsl -lcurses" "LNKFLAGS = -s" #PFU Compact A Series UNIX System V R3, SX/A TISP V10/L50 (Japan) #Maybe the -i link option should be removed? sxae50: @echo 'Making C-Kermit $(CKVER) for PFU SX/A V10/L50...' $(MAKE) wermit \ "CFLAGS= -DSVR3 -DDIRENT -DsxaE50 -DTCPSOCKET $(KFLAGS) -i -O \ -DKANJI" "LNKFLAGS= " #Olivetti X/OS R2.3, 3.x. #NOTES: # . If you build the executable on 2.x X/OS, it will also run on 3.x. # . If you build it on 3.x X/OS, it will NOT run on 2.x. # . Kermit can run with no privileges unless the uucp lines are protected, # in which case kermit must be owned by uucp with suid bit set: # chown uucp kermit ; chmod 4111 kermit. xos23: @echo 'Making C-Kermit $(CKVER) for Olivetti X/OS...' $(MAKE) wermit \ 'CFLAGS=-OLM -DOXOS -DTCPSOCKET -DHDBUUCP -DDYNAMIC $(KFLAGS)' \ "LIBS=" "LNKFLAGS=" #As above, but with curses. xos23c: @echo 'Making C-Kermit $(CKVER) for Olivetti X/OS with curses...' $(MAKE) wermit \ 'CFLAGS=-OLM -DOXOS -DTCPSOCKET -DHDBUUCP -DDYNAMIC -DCK_CURSES \ $(KFLAGS)' "LIBS=-lcurses" "LNKFLAGS=" #Clean up intermediate and object files clean: @echo 'Removing object files...' -rm -f ckcmai.$(EXT) ckucmd.$(EXT) ckuusr.$(EXT) ckuus2.$(EXT) \ ckuus3.$(EXT) ckuus4.$(EXT) ckuus5.$(EXT) ckcpro.$(EXT) ckcfns.$(EXT) \ ckcfn2.$(EXT) ckcfn3.$(EXT) ckuxla.$(EXT) ckucon.$(EXT) ckutio.$(EXT) \ ckufio.$(EXT) ckudia.$(EXT) ckuscr.$(EXT) ckwart.$(EXT) ckuusx.$(EXT) \ ckuusy.$(EXT) ckcnet.$(EXT) ckuus6.$(EXT) ckuus7.$(EXT) ckusig.$(EXT) \ ckcmdb.$(EXT) ckcpro.c wart #Run Lint on this mess for the SUN/BSD version. lintsun: @echo 'Running Lint on C-Kermit $(CKVER) sources for SunOS version...' lint -x -DSUNOS4 -DDIRENT -DTCPSOCKET -DSAVEDUID -DDYNAMIC \ ck[cu]*.c > ckuker.lint.sun lintbsd: @echo 'Running Lint on C-Kermit $(CKVER) sources for BSD 4.2 version..' lint -x -DBSD4 -DTCPSOCKET ck[cu]*.c > ckuker.lint.bsd42 lints5: @echo 'Running Lint on C-Kermit $(CKVER) sources for Sys V version...' lint -x -DATTSV ck[cu]*.c > ckuker.lint.s5 lintmips: @echo 'Running lint on C-Kermit $(CKVER) sources for MIPS version...' lint -DMIPS -DDIRENT -DPID_T=int -DGID_T=gid_t \ -DUID_T=uid_t -DNOJC ck[cu]*.c > ckuker.lint.mips ckuuid: @echo 'building C-Kermit $(CKVER) set-UID/set-GID test programs' $(CC) -DANYBSD -DSAVEDUID -o ckuuid1 ckuuid.c $(CC) -DANYBSD -o ckuuid2 ckuuid.c $(CC) -DANYBSD -DNOSETREU -o ckuuid3 ckuuid.c $(CC) -DANYBSD -DSETEUID -DNOSETREU -o ckuuid4 ckuuid.c $(CC) -o ckuuid5 ckuuid.c @echo 'Read the top of ckuuid.c for directions...for testing' @echo 'you must make these programs setuid and setgid' #Remember TECO? love: @echo 'Not war?'